background image

Page 9 of 44

P/N 595189-01  Rev A  4/10

7

  Hansen is a registered trademark of Tuthill Corporation.

8

  Foster is a registered trademark of Foster Manufacturing Co., Inc. 

9

  Schrader is a registered trademark of Scovill, Inc. 

10 

Cejn is a registered trademark of Cejn AB

Single Plug Version         Dual Plug Version

AIRLINE CONNECTION HOSES

figure 1

WArning

do  noT  uSe  oTher  hoSeS,  couPlingS 

or AdAPTerS To ATTAch incomPATible 

comPonenTS  To  The  reSPirATor.  in-

comPATible  comPonenTS  mAy  reduce 

The AbiliTy of The reSPirATor To SuP-

Ply  Air  And  mAy  exPoSe  The  uSer  To 

The  hAZArdouS  ATmoSPhere  Which 

could  reSulT  in  SeriouS  inJury  or 

deATh.

WArning 

The uSer of ThiS reSPirATor mAy hAve 

To  diSconnecT  The  hoSe  couPling 

Suddenly And  under  STreSSful  con-

diTionS. The uSer muST be Able To diS-

connecT The couPling under The con-

diTionS  Which  mAy  be  encounTered 

during uSe, for exAmPle, WiThouT be-

ing  Able  To  See  The  couPling,  WiTh 

gloveS  on,  WiTh  one  hAnd,  eTc.  fAil-

ure To AdeQuATely TrAin The uSer mAy 

reSulT in SeriouS inJury or deATh.

The 30010-Series, 26370-Series, 200820-Series, and 803904-01 air 

supply  hoses  may  be  interchanged  to  supply  a  single  SKA-PAK AT 

respirator, and, except for these, different types of supply hose may 

NOT be mixed.

The  30010  series  hose  utilize  a  Hansen

7

  brass  disconnect  coupling. 

The  26370  series  hose  utilizes  a  stainless  steel  Foster

8

  disconnect 

coupling. The 26369 series hose utilizes a stainless steel Hansen HK 

disconnect coupling. The 30020 series hose utilizes a steel Schrader

9

 

disconnect coupling. The 805659 series hose utilizes a brass Cejn

10

 

disconnect  coupling.  One  of  these  types  of  couplings  is  located  on 

the end of the airline connection hose and at the ends of each seg-

ment  of  air  supply  hose.  Dual  airline  connection  hoses  terminate  in 

two couplings, both of which are of one of the above types. 

The air supply hose segments must be directly coupled to the airline 

connection hose at the waist belt of the respirator, to each other and 

to the air supply system. Adapters shall not be used. 

After  determining  which  type  of  air  supply  hose  and  couplings  are 

used with your respirator, locate the appropriate section of Table 1 on 

page 23 of this instruction sheet for detailed instructions on operating 

the coupling and for limitations on air supply hose length and number 

of segments allowed. 

figure 2

Summary of Contents for SKA-PAK AT













































Reviews: