background image

    

 

SHENZHEN SHUANGCHITECHNOLOGY CO.,LTD

 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including 
interference that may cause undesired operation. 
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment. 
 
FCC Radiation Exposure Statement   
The modular can be installed or integrated in mobile or fix devices only. This 
modular cannot be installed in any portable device, for example, USB dongle 
like transmitters is forbidden. 
 
This modular complies with FCC RF radiation exposure limits set forth for an 
uncontrolled environment. This transmitter must not be co-located or operating 
in conjunction with any other antenna or transmitter. This modular must be 
installed and operated with a minimum distance of 20 cm between the radiator 
and user body. 
 
If the FCC identification number is not visible when the module is installed 
inside another device, then the outside of the device into which the module is 
installed must also display a label referring to the enclosed module. This 
exterior label can use wording such as the following: “Contains Transmitter 
Module FCC ID: 2ADVXM5Q10-B Or Contains FCC ID: 2ADVXM5Q10-B

 

 
When the module is installed inside another device, the user manual of this 
device must contain below warning statements; 
1. This device complies with Part 15 of the FCC Rules. Operation is subject to 
the following two conditions: 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference 
that may cause undesired operation. 
2. Changes or modifications not expressly approved by the party responsible 
for compliance could void the user's authority to operate the equipment. 
The devices must be installed and used in strict accordance with the 
manufacturer's instructions as described in the user documentation that comes 
with the product 

Summary of Contents for M5Q10-B










Reviews: