background image

Galaxy 2000RS-2W  -  Page 13

System  Wiring

6-Pin Starter Harness

Pin 1

RED WIRE A

: Main Power Input A (+). Connect to the battery or constant power wire at the ignition

switch with a minimum 25 Amp supply. Remove fuse until installation is complete and wiring is checked. 

Pin 2

RED WIRE B

: Main Power Input B (+). Connect to the battery or constant power wire at the ignition

switch with a minimum 25 Amp supply.  Note: if connecting at the ignition switch it is highly

recommended to use separate power wires for each Red wire, each with a minimum 30A supply.

Remove the fuse until the installation is completed and all wiring is checked. 

Pin 3

BROWN WIRE

: Second Ignition Output (+). The Brown wire pr12V for a second ignition

wire. This wire may instead be programmed for use as a second accessory or second starter wire.

Pin 4

ORANGE WIRE

: Accessory Output (+).  Connect to the accessory wire coming from the ignition

switch that supplies power to the heater/air-conditioner.  Some cars may have multiple accessory wires. 

Pin 5

YELLOW WIRE

: Ignition Output (+).  Connect to the main ignition wire that pr12V when the

ignition is on and while cranking the starter. 

Pin 6

VIOLET WIRE

: Starter Output (+). Connect to the the vehicle’s starter wire.

20-Pin Main Harness

Pin 1

GREEN/WHITE WIRE

: Brake Input (+).  Connect to the wire that shows +12V when pressing the

brake.  The Green/white wire is a safety shutdown wire that must be connected.

Pin 2

BLACK/GRAY WIRE

: Tach Input. Connect to the vehicle’s tach wire or a fuel injector wire if the

tachless mode does not provide satisfactory operation.

Pin 3

WHITE/RED WIRE

: Auxiliary 2 Output (-) 500 mA. Connect to a relay or module for an optional

feature such as power window activation, etc. This output may be programmed for momentary, timed,

or latched operation.

Pin 4

BLACK/WHITE WIRE

: Dome Light Output (-) 500 mA. Connect to the wire that activates the

vehicle’s dome light, usually the door pin switch wire. NOTE: The dome light output can usually connect

to the same wire used for the door trigger input (see Green and Violet door trigger wires).

Pin 5

YELLOW WIRE

: +12V Ignition Input.  The Yellow wire must connect to a main ignition wire at the

ignition harness. This wire must show +12V when the ignition is on and while cranking the starter. The

voltage must not drop when the car is starting.

Pin 6

BLUE/YELLOW WIRE

: Glow Plug Input (+). For vehicles equipped with diesel engines the

Blue/yellow wire must be connected to the wait-to-start light in the gauge panel.  This wire will show

+12V when the light is on, and ground when the light turns off.  If the wait-to-start wire shows ground

when the light is on, a relay must be installed (see wiring diagrams).

Pin 7

BLUE/WHITE WIRE

: Passenger Unlock Output (-) 500 mA. Connect to a relay to unlock the

passenger doors when the system is configured for Driver Priority Unlocking. 

Pin 8

BLUE/ORANGE WIRE

: Ground When Running Output (-) 500 mA. Connect to an optional factory

security bypass module if required. 

Pin 9

BLACK WIRE

: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away

any paint or dirt to insure the best possible ground.   

Pin 10

RED WIRE

: Module Power Input (+). Connect to a constant source of +12V.

Pin 11

VIOLET WIRE

: Positive Door Input (+).  Connect to the door switch circuit wire that shows +12V

when the door is open.  This type of door circuit is usually found on Ford vehicles.

Pin 12

GREEN WIRE

: Negative Door Input (-).  Connect to the door switch circuit wire that shows ground

when the door is open.

Summary of Contents for Galaxy 2000RS-2W





























Reviews: