P:\INSTALLATION INST\Access Controls\INST-923\INST-923.vsd Rev F 05-19 Page 2
CAUTION
IF THE UNIT IS AC POWERED, MAKE SURE
THAT THE SECONDARY OF THE SYSTEM IS
ISOLATED FROM EARTH GROUND
Test your new user
Enter PIN code ‘2580#’. The green indicator should illuminate and the main relay
should activate, unlocking the door for 5 seconds.
Assign a user code
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
01# 002# 2580# 2580# 1#
Assign User 002 with a PIN code of ‘2580’.
Activate the main relay when entered.
Step 3. Enter:
#
Exit programming mode
Deleting a user code
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
02# 002# 002#
User 2 has been deleted.
Step 3. Enter:
#
Exit programming mode
Adding additional user codes
Once the code length and relay time has been set you do not need to set them again for
additional users.
To add additional users:
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
01# 003# 2222# 2222# 1#
User 003 has been created with a PIN code of
‘2222#’ to activate the main relay
Step 3. Repeat Step 2 to enter another unique User # & PIN code OR skip to Step 4.
Step 4. Enter:
#
Exit programming mode
RED/GREEN
POWER/ACCESS
INDICATOR
YELLOW
“PROGRAM”
INDICATOR
KEYPAD
FRONT
Set default parameters (first time use)
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
03# 4#
Set the entry code length to 4 digits
Step 3. Enter:
21# 5#
Set the main relay activation time for 5 sec.
Step 4. Enter:
#
Exit programming mode
QuickStart Programming
You must first enter programming mode to perform any function. The yellow indicator will blink slowly showing that the 923
EntryCheck™ is in programming mode. Use the option codes to program each function. After the new data entry is complete for
each function , the yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the
programming has been accepted. The red indicator will light if any programming data is entered incorrectly or the function is rejected.
If a red indicator is seen, the entire function (option code + data) will have to be fully re-entered.The keypad will remain in
programming mode until # is pressed or after 30 seconds of inactivity.
BLACK
PINK/SALMON
GREEN
GRAY
BLACK
VIOLET
BLACK
BLUE
DOOR POSITION
SWITCH
[N/C]
REQUEST-TO-EXIT
SWITCH
[N/O]
GROUND
OUTPUT #4
OUTPUT #3
GROUND
SENSE
REQUEST TO EXIT
GROUND
E1
E8
E7
E6
E5
E4
E3
E2
C
NO
C
NC
NO
AUXILIARY OUTPUTS
100mA MAX TO COMMON
{
*
*
NOT USED
NC
TO POWER SUPPLY
KEYPAD POWER
12 or 24 VOLTS
AC OR DC
}
+
-
RED
BLACK
AUXILIARY RELAY
2 AMPS @ 28VDC MAX
}
NO
COM
ORANGE
WHITE
BLACK
MAIN RELAY
5 AMPS @ 28VDC MAX
}
NO
COM
NC
ORANGE
WH
ITE
YE
L
LO
W
POWER
WIRE
HARNESS
(E1-E8)
ANTI-TAMPER
SWITCH
AUXILIARY
RELAY
BACK
JP1
MAIN
RELAY
JP2
Grn Wire
To earth ground
Fig. 2 Wiring Pigtail Color Code
