P:\INSTALLATION INST\Delayed Egress\INST-S6000-101.vsd Rev D.1 10-19 Page 4
Device Wiring Pigtail
THIS PRODUCT MUST BE POWERED BY A 600 SERIES POWER SUPPLY:
Single Door – 602RF 1 AMP
Double Door – 631RF 1.5 AMP
3
A DOOR CONTACT IS REQUIRED FOR ANTI-TAILGATE, BOCA AND DOOR PROP FUNCTIONS.
4
WIRING SHALL BE CONNECTED TO AN ACCESSORY WITHIN THE PROTECTED AREA AND UNUSED WIRE MUST BE CAPPED OFF.
2
Max Operating Temperature: 0 C to 70 C
Tested to 85% RH @30 C
Enviromental:
Input Voltage : 24VDC +/- 10%
Slave Output : 24VDC @250ma
Monitor Relays: 1 Amp contacts @12/24vdc
Input Current : 540ma Max
Electrical Specifications:
GRY = DPS
1,4
ORG = Slave Out
1
VIO = Remote Trigger
1
BRN = Red Relay
1
GRN = Green Relay
1
YEL = Relay Common
1
BLU = Reset / REX
1
WHT = Bypass
1
RED = Power In (+)
3
BLK = Power In (-)
3
(24VDC)
(For pairs of doors)
(24vdc @ 250ma)
Wire Color
Wire Designation
Description
Used
for
a
pair
of
doors
(master
&
slave).
This
is
a
voltage
output
(24VDC
@250mA).
Connect
this
wire
to
+24VDC
(Red
wire)
of
the
slave
bar.
See
"Typical
Wiring
for
Single
or
Double
Door
Installation".
Used
for
a
pair
of
doors
(master
&
slave).
This
is
a
dry
input.
Connect
this
wire
to
one
leg
of
the
Slave
Trigger
output.
The
other
leg
of
the
Slave
Trigger
output
is
connected
to
ground
(
‐
VDC).
Closing
the
switch
shorts
this
wire
to
ground
and
initiates
the
alarm
sequence.
See
"Typical
Wiring
for
Single
or
Double
Door
Installation".
The
two
white
wires
on
the
slave
bar
are
the
Normally
Open
trigger
switch.
Brown
Red
Relay
This
is
the
Alarm
Relay
Output
(Dry,
1A@12/24VDC).
It
is
normally
INACTIVE
when
the
door
is
secure.
It
changes
state
when
the
bar
is
pressed
beyond
the
nuisance
delay
and
placed
into
an
Alarm
state.
It
may
be
configured
as
Normally
Open
OR
Normally
Closed
using
Jumper
J7.
The
YELLOW
wire
is
the
relay
common.
Green
Green
Relay
This
is
the
Door
Secure
Relay
Output
(Dry,
1A@12/24VDC).
It
is
normally
ACTIVE
when
the
door
is
secure.
It
changes
state
when
the
bar
unlocks
after
(a)
the
delayed
egress
countdown
expires,
(b)
an
authorized
Request
‐
to
‐
Exit(REX)
signal,
or
(c)
the
bar
is
Bypassed.
It
may
be
configured
as
Normally
Open
OR
Normally
Closed
using
Jumper
J6.
The
YELLOW
wire
is
the
relay
common.
Yellow
Relay
Common
This
is
the
shared
relay
common
for
both
the
Red
&
Green
Relay.
Grey
Door
Position
Switch
(DPS)
This
is
a
dry
input.
Connect
this
wire
to
one
leg
of
a
Door
Contact
switch.
The
other
leg
of
the
Door
Contact
switch
is
connected
to
ground
(
‐
VDC).
The
Door
Contact
polarity
must
be
OPEN
when
the
door
is
closed.
A
door
contact
is
required
for
anti
‐
tailgate
and
door
prop
alarm
functions.
This
is
a
momentary,
dry
input.
Connect
this
wire
to
one
leg
of
a
Normally
Open
switch.
The
other
leg
of
the
Normally
Open
switch
is
connected
to
ground
(
‐
VDC).
When
the
bar
is
in
a
secure
state,
shorting
this
input
will
result
in
an
authorized
unlock
(REX).
The
REX
period
is
configured
by
the
dip
switch
settings.
When
the
bar
is
in
an
alarm,
authorized
unlock
state,
or
in
a
bypassed
state,
shorting
this
input
will
reset
(secure)
the
bar.
White
Bypass
This
is
a
momentary,
dry
input.
Connect
this
wire
to
one
leg
of
a
Normally
Open
switch.
The
other
leg
of
the
Normally
Open
switch
is
connected
to
ground
(
‐
VDC).
When
the
bar
is
in
a
secure
state,
shorting
this
input
will
unlock
the
device
indefinitely,
until
the
bar
is
Reset.
Red
Power
IN
(+)
24VDC
Black
Power
IN
(
‐
)
24VDC
Input
Voltage:
24VDC
+/
‐
10%;
Input
Current:
540mA
(max).
The
Red
&
Black
wires
are
the
minimum
required
connections
for
a
single
door
application.
Blue
Reset/REX
Orange
Slave
Out
Remote
Trigger
Violet
MAXIMUM CONNECTED WIRING LENGTH PERMITTED IS 98.5 FT. (30).
1
