background image

Section 3 General information

W A R N I N G

 

This product can expose the user to chemicals with silica, crystalline (airborne particles of
respirable size), which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to 

www.P65Warnings.ca.gov

.

3.1 Warranty

Refer to the manufacturer's website for warranty information (seabird.com/warranty).

3.2 Service and support

The manufacturer recommends that sensors be sent back to the manufacturer annually to
be cleaned, calibrated, and for standard maintenance.
Refer to the website for FAQs and technical notes, or contact the manufacturer for
support at support@seabird.com. Do the steps below to send a sensor back to the
manufacturer.

1.

Complete the online Return Merchandise Authorization (RMA) form or contact the
manufacturer.

Note: The manufacturer is not responsible for damage to the sensor during return shipment.

2.

Remove all batteries from the sensor, if so equipped.

3.

Remove all anti-fouling treatments and devices.

Note: The manufacturer will not accept sensors that have been treated with anti-fouling

compounds for service or repair. This includes AF 24173 devices, tri-butyl tin, marine anti-

fouling paint, ablative coatings, etc.

4.

Use the sensor's original ruggedized shipping case to send the sensor back to the
manufacturer.

5.

Write the RMA number on the outside of the shipping case and on the packing list.

6.

Use 3rd-day air to ship the sensor back to the manufacturer. Do not use ground
shipping.

7.

The manufacturer will supply all replacement parts and labor and pay to send the
sensor back to the user via 3rd-day air shipping.

3.3 China RoHS disclosure table

Name of Part

Hazardous substance or element in product

Pb

Hg

Cd

Cr(VI)

PBB

PBDE

PCBs

X

O

O

O

O

O

Cables

X

O

O

O

O

O

Housing

O

O

O

O

O

O

Mounting hardware

O

O

O

O

O

O

Accessories

O

O

O

O

O

O

This table is compiled to the SJ/T 11364 standard.

O: This hazardous substance is below the specified limits as described in GB/T 26572.
X: This hazardous substance is above the specified limits as described in GB/T 26572.

11

Summary of Contents for SUBMERSIBLEBATTERYPACKS

















Reviews: