background image

 

Page 10 of 11

 

 

123-

652 Rev - 

 

 

 
 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
OWNERS RECORD 
Installation Date ______________________ 
Installer       ________________________ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

For More Information Call 

Sea-Fire Marine  

Phone: 1(410) 687 5500 

Fax: 1 (410) 687 5503 

www.Sea-Fire.com

       

 

Manufacturer of Quality Fire, Suppression and Detection Systems 

This manual will be revise frequently to keep up-to-date with new changes and development. 

“Sea-Fire Marine, an ISO 9001 registered company, is fully committed to exceeding our Customer’s expectations.” 

ONE YEAR LIMITED WARRANTY 
We guarantee to the original retail purchaser of the Sea-Fire Machinery Shutdown Restart 
System for a period of one (1) year after retail purchase against defective material and 
faulty workmanship.  Any Engine Interrupt System found to be defective during the 
warranty period will be replaced or repaired free of charge upon the prepaid return of the 
defective system. 
This warranty provides specific legal rights and you may have other rights, which vary from 
country to country. 
 

 

Summary of Contents for 131-740












Reviews: