background image

Aqua Whisper DX Modular 450-1800

 

Page 9-3

Troubelshooting

 

Solution

:  Clean all marine growth and debris from 

the Inlet Thru-Hull Fitting.

 

System is newly installed and operation is being 
performed for the first time. The feed water 
pressure is low and insufficient to keep the 
System in operation.

 

A NEW boat, or newly installed System, may have 
protective shipping tape covering the Inlet Thru-
Hull Fitting. A New boat, or newly installed System, 
may have manufacturing debris such as caulking 
slopped over the Inlet Thru Hull or a rag may be 
stuffed into the Inlet Thru-Hull fitting. A NEW Inlet 
Thru-Hull Fitting may have casting slag, that has 
not been machined off, partially covering the 
“fingers” or the inside of the fitting.

 

Solution

:  Inspect the Inlet Thru-Hull Fitting and 

clean all manufacturing debris and casting slag 
from the fitting.

2) 

SEA COCK VALVE

The Sea Cock Valve is usually a 1/4 turn Ball  
Valve although any positive closing and opening valve is 
acceptable.
Problems and Symptoms appearing and caused by the 
SEA COCK VALVE:
a) 

The Sea Cock Valve is closed when attempting to 
Start the System.

 

System does not register feed water flow and feed 
water pressure when attempting to start. An error 
screen appears and the System shuts down.

 

When the System is not in use it is good practice, 
for the safety of the Boat, to close the Sea Cock 
Valve. Don’t forget to open it prior to starting the 
System.

 

Solution

:  Open the Sea Cock Valve.

b) 

The Sea Cock Valve seal is worn or the seal is 
loose causing air to enter the System Feed Line.

 

System feed water pressure is low and insufficient 
to keep the System in operation. This section of 
the Feed Line is under a vacuum condition when 
the System is in operation. If the valve’s seal is 
worn or loose air can enter the feed line causing 
the System to lose pressure.

 

Look for air bubbles moving through the Sea 
Strainer, or feed line.
 

Solution

:  Change the valve seals, tighten 

them, or if necessary replace the valve.

attributed to improper installation, is the 
liability of the installer, and is not covered 
by the Sea Recovery warranty.

CAUTION

!  If the Sea Recovery 

System is connected to a Sea Chest or 
Stand Up Pipe, do not plumb the Sea 
Recovery System feed line to the “top” 
of the Sea Chest or Stand Up Pipe. If 
plumbed into the top of these feed water 
arrangements, the Sea Recovery System 
will experience continual shut down due 
to air inducement into the system. The 
resulting failure of the system to remain 
in operation is attributed to improper 
installation, is the liability of the installer, 
and is not covered by the Sea Recovery 
warranty. Plumb the Sea Recovery System 
to the “bottom” of such feed water 
arrangements to ensure a continual air free 
supply of feed water to the system.

1) 

THRU-HULL INLET FITTING

Problems and Symptoms appearing and caused by the 
THRU-HULL INLET FITTING:
a) 

Flat profile Inlet Thru Hull Fitting:

 

System runs fine when at anchor. However, 
when under way the System shuts off due to low 
pressure or low feed water flow.

 

A flat profile Inlet Thru Hull Fitting will cause a 
vacuum at the System’s feed line cavitating the 
Booster Pump and reducing the efficiency of the 
Booster Pump resulting in low feed water pressure 
and low feed water flow.

 

Solution

 

Change the flat profile Thru Hull Fitting to a 
forward facing scoop.

b) 

Debris is blocking the Inlet Thru Hull Fitting:

 

System feed water pressure is low and insufficient 
to keep the System in operation.

 

Marine growth or debris such as a plastic bag or 
rag covering the Inlet Thru-Hull Fitting will cause 
a vacuum at the System’s feed line cavitating the 
Booster Pump and reducing the efficiency of the 
Booster Pump resulting in low feed water pressure 
and low feed water flow.

Summary of Contents for Aqua Whisper DX 1400-2



































































































































































































































Reviews: