Aqua Whisper DX Modular 450-1800
Page 5-5
Installa
tion
TUBING AND HOSE PRECAUTIONS
TUBE FITTING CONNECTIONS ASSEMBLY
a.
Cut tube end square and clean.
b.
Loosen nut on fitting three turns.
c.
Insert tube into fitting until it bottoms.
d.
Loosen nut completely and remove tube with
attached parts from body.
e.
Check to ensure that the O-Ring is seated onto the
tube under the spacer.
(and not pinched into the body)
f.
Insert tube with attached parts into the body and
tighten nut finger tight.
CAUTION
(Refer to fig. 5c, pg 5-5)
:
Always allow slack in all tube and
hose lines. Never cause the tube or
hose to immediately bend from the
fitting. Allow the line to enter or leave
from the fitting in a straight manner
for several inches to ensure proper
connection, to relieve stress to the fitting
and tube or hose, and to allow ease of
detachment and reattachment during
maintenance or repair.
If water lines are pulled tight causing them to bend at the
fitting they will leak, allow air to enter, fail prematurely,
and or break the fitting that they are attached to.
5.3 INTERCONNECTING COMPONENTS
INTERCONNECTING COMPONENTS WITH SUPPLIED HOSE
Chart Available on Page 5-6
1.
Using the supplied 3/4 in. (19 mm) I.D.
clear braided hose connect the Suction Line
components, Low Pressure line components, and
Brine Discharge Line components:
Secure each connection with the supplied
hose clamps. Ensure all Suction Hose connections
use two hose clamps rotated 180 degrees with
the screw heads facing the same direction.
Remove any flash on the Hose Barb fittings
using fine sandpaper.
If your System is not supplied with a mentioned
optional component then skip it and connect to the
next supplied component.
2.
With the supplied 1/2 in. (12.7 mm) I.D. clear
braided hose connect the Feed Water Line
components and secure each connection with the
supplied hose clamps, placing 1 hose clamp onto
each hose barb fitting:
3.
3/8 in. (9.5 mm) OD nylon tubing is supplied with
applicable components for connecting Product
Water and FWF components. Use or non use of
the 3/8 in. (9.5 mm) OD nylon tubing is dependent
upon Product Water and FWF options installed.
4.
1/4 in. (6.35 mm) OD nylon tubing is supplied
with applicable components for connecting
Pressure Pick Up points to the Low Pressure
Transducers. Use or non use of the 1/4 in.
(6.35 mm) OD nylon tubing is dependent upon
Prefiltration options installed.
5.
Ensure all High Pressure Hoses supplied for the RO
Pressure Vessel assembly have sufficient slack and
are not pulled tight into a sharp or immediate bend.
5.4 WATER TANK
CUSTOMER SUPPLIED FRESH WATER TANK, HIGH AND
LOW LEVEL SWITCHES, AND ALARM
Not Numbered on the Piping and Interconnect
Diagram. Installed inside the Fresh Water Tank.
These two tank level switches are not necessary for
operation of the System. They do add additional features
Figure 5c - Always allow slack in all tube and hose lines.
Summary of Contents for Aqua Whisper DX 1400-2
