Aqua Whisper DX Modular 450-1800
Page 5-10
Installa
tion
NOTE
! To remove
tube from fitting, first
remove the C-clamp
then push fitting
sleeve down. Once
the fitting sleeve is
down, pull the tube out of the fitting.
Install Ultraviolet Lamp
Perform this procedure only after the quartz sleeve
installation and leak-tests are completed successfully
1.
Connect the UV lamp to the 4-point receptacle.
If the lamp is not installed properly, lamp breakage
will occur.
2.
Insert lamp into quartz sleeve through
compression nut pass-thu.
3.
Install rubber boot over compression nut.
4.
Connect unit power cable to power source.
5.
Tighten the 4 screws to secure ballast box cover.
6.
Turn ON the power to the unit.
7.
Verify UV lamp operation from the viewport.
8.
Allow one minute for the UV lamp to warm up prior
to flowing water through the UV unit.
CAUTION
! Use the viewport to verify the
proper operation of the UV lamp.
7.
Lubricate the tips of the quartz sleeve with clean
water and insert new O-ring. Ensure the O-ring
has all-round contact with the cylinder pass-thru.
8.
Tighten the compression nut while making sure
the nut does not contact the quartz sleeve. Adjust
O-ring position as necessary. The compression nut
should be snug and tight, not over-torque.
9.
Repeat Step 7 and 8 on the ballast box
compression nut.
Connect Plumbing
Tube or hose ends must be cut squared and clean; must
have no rough edges. The quick fit elbow fitting has a
C-clamp that will lock the tube in place once inserted.
1.
Insert the supply pipe into one cylinder port and
label the port “Inlet”.
2.
Insert the temporary pipe into the other cylinder
port to direct water into a container.
3.
Slowly fill the cylinder with water and flush
cylinder for 1 minute.
4.
Remove temporary pipe and insert the return pipe
into the cylinder port and label the port “Outlet”.
5.
Slowly pressurize the UV unit by filling the cylinder
with water while checking for leaks.
6.
If leaks are found on the compression nuts,
depressurize the unit and slightly tighten the
leaking compression nut.
7.
Retest until a leak-free installation is verified.
8.
Once UV unit is leak-free, the quartz sleeve
installation is complete and the UV lamp can
be installed.
Summary of Contents for Aqua Whisper DX 1400-2
