9711QOR-86 C & Ku-Band TXRX
Bluetooth Installation & Operation
21-3
21.5.
Removing the ADE Bluetooth Hardware
1.
Turn Tracking OFF at the Antenna Control
unit.
2.
At the ADE, open the hatch in the base of
the radome.
3.
Reach into the radome hatch to secure the
AC power at the breaker.
4.
Rotate the antenna pedestal to access the
PCU.
5.
Carefully enter into the radome hatch, far
enough to reach the PCU.
6.
Remove the SERIAL Bluetooth dongle
(Receiver) to the MK2 PCU Service Port. If
the devices retaining screws were secured,
unscrew them to remove the device from
the PCU.
7.
Carefully exit the radome hatch.
8.
Reach into the radome hatch to turn AC
power ON at the breaker.
9.
Allow the antenna to re-Initialize.
10.
Secure the radome hatch.
11.
Re-target the satellite if desired.
12.
Return to normal operation
21.6.
Removing the BDE Bluetooth Hardware
1.
At the computer, remove the Bluetooth
Transmitter from the computer USB port.
2.
Close the Sea Tel diagnostic programs
(ProgTerm or DacRemP) which were being
used.
3.
You are now ready to return to normal
operation of your Sea Tel antenna system.
21.7.
Installing Software via Bluetooth
You can update the MK2 PCU software, and/or the DAC software, using the Bluetooth connection.
NOTE: You can NOT use the Bluetooth connection to update software in the CommIF, SCPC Receiver, 400MHz
Modems or the Motor Driver Enclosure (MDE). If you need to update software in any of these assemblies you must
install the software from a direct connection to the ACU.
1.
With Bluetooth hardware installed and setup per the “Installing the ADE Bluetooth Hardware “ and “Installing
the BDE Bluetooth Hardware “ paragraphs above.
2.
From the computer, open ProgTerm.
3.
It is strongly recommended that you save a parameter dump of the ACU & PCU parameters.
Summary of Contents for 9711QOR-86
