background image

Fig. 10

points.
f) The top guide must be manufactured and installed so that the gate is 
perfectly upright.
g) Physical gate stops must be fitted to prevent the gate coming out of 
its guides and track.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

1/2”

1/4”

5”

Fig. 7

Install the warning signs, on both sides of the gate which   informs   the 
pedestrians about the danger they run when passing or resting in the 
environment of the gate (fig. 10). 

 

Important:
For a higher security, SEA advices to install infrared photocells.

2. PRECAUTIONS

Lepus has been created for the automation of gates used by vehicles 
only. Pay very much attention to avoid   the crossing of the gate path it is   
very dangerous for pedestrians (fig. 8).

Make sure that no person not belonging to the company somehow 
activates the automation or acts on it from the outside (fig. 9).

GATE WARNINGS AND PRECAUTIONS

!!

WARNING

Moving Gate Can Cause

Serious Injury Or Death 

-  KEEP CLEAR !  Gate may move at any time 
without prior Warning.
-  Do not let children operate the gate or play in 
the gate area.
-  This entrance is for vehicle only.
   Pedestrians must use separate entrance

!!

A N G

R I

W

N

A N G

R I

W

N

a

s

au

v

M

a

e

i

C

  e

t C

n

o

G

y

 In

 O

j

 D

i

r

er

h

u

t  

r

s

ou

a

S

e

E

!

 

m

 

 

E

 

E

 

K

y

a

t

 

AR

t

e

L

y

-

P

a

a

C

 

 

v

n

e

o

a

m

 

 

 

 

i

G

t

e

m

u

in

o

r

w

a n

r

ri

W

h

 

 

o

.

p

t

i

t

g

o

 

a

y

 

e

D

 

e

n

l

l

r

t

g

r

 

a

-

i

r

t

e

d

 

l

a

 

e

p

h

o

e

o

e

h

 

n

c

p

 

 

t

 

n

t

o

 

i

t

 

h

e

t

t

a

.

 

r

g

a

e

e

a

 

 

T

f

e

 

 

l

t

s

i

i

 

-

n

c

e

e

 

h

l

i

y

c

r e

s

n

 

n

r

h

v

.

o

o

a

 

e

e

m

 

u

e

 

 

 

d

t

p

c

 

 

s

e

e

P

n

e

r

t

n

s

r

s

r

i

 

e

a

u

a

a

t

a

t

s

s

n

Fig. 9

Fig. 11

3. TYPE OF INSTALLATION

A front installation is the right and only possible installation, it is highly 
recommended to install two security gate stops on the two extremities of 
the rail to prevent the gate from derailment (fig. 11).

Fig. 8

Over-Travel Stop

Over-Travel

Stop

®

International registered trademark n. 2.777.971

5

Cod. 67410022

REV 00 - 12/2013

Summary of Contents for LEPUS 1000













Reviews: