background image

Opening
Electronic Systems

24

MINI TANK E MARK TANK 

ACCESSORIES

SAFETY GATE

ELECTRIC LOCK

PHOTOCELLS

RADIO RECEIVER

TRANSMITTER

EXTERNAL

LOOP DETECTOR

KEY SWITCH

POSITIVE STOPS

FLASHING LAMP

GATE 2

CONTROL UNIT

SUPPORTS 

FOR PHOTOCELLS

KIT EXTERNAL LOCK 

MINI TANK

MARK tANK

MINI TANK

MARK TANK

DECLARATION OF CONFORMITY

SEA declares under its responsibility that the products

MINI TANK, MARK TANK

meet the essential requisites provided for by the following European Directive and following changes:

89/392/CEE (Machine Directive)
89/336/CEE  (Electromagnetic Compatibility Directive)
73/23/CEE (Low Tension Directive)

SAFETY PRECAUTIONS:

All electrical work should conform to current regulations. A 16 A   0,030 A differential switch must be incorporated into the source of 
the operators main electrical supply and the entire system properly earth bonded. Always run mains carrying cables in separate 
ducts to low voltage control cables to prevent mains interference.

INTENDED USE:

The Mini Tank and Mark Tank operators are been designed to be solely used for the automation of   swing   gates. 

SPARE PARTS:

To obtain spare parts contact:

SEA s.r.l. -Zona Ind.le, 64020 S. ATTO   Teramo   Italia

SAFETY AND ENVIRONMENTAL COMPATIBILITY:

Don’t waste product packing materials and/or circuits.

When being transported this product must be properly packaged and handled with care.

LIMIT OF GUARANTEE

The Mini Tank and Mark Tank   operators   are guaranteed for a period of   36 months. The guarantee period starts from the date 
stamp printed on the unit. The Mini Tank and Mark Tank guarantee will be void if the unit has been incorrectly installed, not used for 
the purpose intended, tampered with or modified in any way.
The validity of this guarantee only extends to the original purchaser of the unit.

MAINTENANCE AND OUT OF SERVICE:

The decommission and maintenance of this unit must only be carried out by specialised and authorised personnel.

NOTE: THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY 
IMPROPER USE OF THIS PRODUCT.

   

SEA

 

reserves the right to do changes or variations that may be necessary to its products with no obligation to notice.

REV 01 - 07/2006

Summary of Contents for 620660













Reviews: