background image

Fig. 14

Fig. 15

5

4

5

4

9) Force adjustment

If necessary the force of thrust of the beam can be 
adjusted through the two calibration screws (grey and 
yellow) placed on the side of the hydraulic unit 
(Fig.16). 
*The automation is adjusted at 15 kg force ex works 
so to guarantee the anti-crush safety. We recommend 
to adjust it only in case of necessity.

Fig.16

-

+

English

8)   Beam balancing

-

Release the beam with manual release, so that it is 
free to be opened and closed manually (Fig.18).

-

Place the beam at approx. 45°.

-

Loosen or tighten the spring stretching nut until the 
spring counterbalances the weight of the 45° beam 
(Fig. 14). The best balancing position is obtained when 
the beam reaches the position shown in Fig. 14.

-

After having obtained the balancing, lock the nuts of 
the spring stretcher with the counter nut and re-block 
the motor.

Spring 

 nut

stretching

Anchoring
lock nut

10)   Beam levelling
Note:

 this operation must be carried out only if the beam is not 

perfectly horizontal (closing stage) or vertical (opening stage) at 
the end of its stroke.

-

Release the beam with the special manual release so that it is 
free to open and close manually.

-

Release the screws of the limit switch on unscrewing the nuts 
on the mechanical stops (fig.15).

-

Loosen or tighten the stop screws so that the beam is released 
in its vertical position (opening stage) and horizontal position 
(closing stage) (Fig. 15).

-

After having executed the levelling lock the screws of the limit 
switch tightening the nuts on the mechanical stops and re-lock 
the beam.

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

Cod. 67410035                                                        Rev 06 - 06/2010                                                              

23

Summary of Contents for VELA














Reviews: