background image

4)       Fixation of the balance   

Carefully insert the roll bearing (A) into the hole 1 or 2 of 

the balance in case of left-hand mounting; into hole 3 or 4 
in case of right-hand mounting using hinge P and a nylon 
hammer.

Attention: The choice of the hole varies according to the beam 
length. (SEE BOARD)

Lubricate   with grease the bearing and the washers 

.

Mount the resting devices as shown in Fig. 5

during assembling

5)       Mounting of the spring 

Anchor the spring on the bracket which has been mounted 
before (S) 

Insert the rod of the spring into the bracket (B) and insert the 
nuts (D) without tightening them.

OVAL BEAM

Length

(m)

3

4

5

Balance

position

1 / 4

1 / 4

1 / 4

Spring

(Ø mm)

6

7,5

8,5

Note: Strictly follow the opening time to avoid bad 
working

Note: The springs and the bracket of   anchorage are supplied with the 
beam.

Opening

time

3

4

5

” ÷ 4”

” ÷ 5”

” ÷ 6”

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

Fig.6

A

P

Fig.5

P

A

1

2

3

4

B

D

S

Keep well
lubricated

with grease

14

Cod. 67411465                                                 Rev.00 - 12/2012                                                              

Summary of Contents for VERG 24V










Reviews: