background image

10

English

Unscrew the Torch bottom whilst holding on the handle and extract it from the
lamp body while holding the latter vertical with the optics downward.
Connect the charger to mains and connect it through the appropriate jack to the
outlet located beside the lamp holder
Check that the green led lights up when the charger is connected to mains.
The charging time from flat is shown in the table.
As soon as the needed voltage has been reached, the automatic charger cuts
off the supply and remains in standby mode until disconnected from mains (see
paragraph “Technical Specifications of the Battery Charger”).
When the Torch has been recharged, close it after previously cleaning and
lubricating the O-Rings and relevant seats.
In case of prolonged non-use, carry out a complete discharging-charging cycle
every three months (discharge with submerged Torch).
All Torches are equipped with a battery protection electronic circuit, which
disconnects the feed current when the voltage drops under a specified threshold
and prevents possible polarity inversion, which would cause irreparable damage
to the batteries.
However, avoid leaving the torch under charge for long periods of time.

W A R N I N G

never switch on the torch outside the water
never unscrew the torch head or bottom during diving or if wet

C H E C K S   B E F O R E   D I V I N G

Check for perfect seal of the body.
When in water, check, by immersing the torch, that there is no continuous
discharge of air bubbles from the case.

F L O O D I N G

In case of flooding, open the torch and immediately rinse inner parts in fresh water,
then wipe with a cloth and with an air source paying particular care to the electronic
circuit. Remove the oxide, if any, formed on metal parts and immediately proceed
to recharge.
If the quantity of water leaked inside the torch is considerable and if it has remained
there for a long time, it is recommended to cut and remove the plastic protection film
and then proceed as described above.

L I M I T S   O F   U S E

The maximum operating depth is 100 m.
Owing to the high temperatures reached by the lamp, it is recommended to use
the torch ONLY underwater.

Summary of Contents for SeaRay Plus Series









Reviews: