background image

 

Warranty 

Sealevel Systems 

COMM+4.PCI

 

Page 

16

 

Warranty 

Sealevel Systems, Inc. warrants this product to be in good working order for a 
period of one year from the date of purchase. Should this product fail to be in 
good working order at any time during this period, Sealevel Systems will, at its 
option, replace or repair it at no additional charge except as set forth in the 
following terms. This warranty does not apply to products damaged by misuse, 
modifications, accident or disaster. 
 
Sealevel Systems assumes no liability for any damages, lost profits, lost savings 
or any other incidental or consequential damage resulting from the use, misuse 
of, or inability to use this product. Sealevel Systems will not be liable for any 
claim made by any other related party. 
 

RETURN AUTHORIZATION MUST BE OBTAINED FROM SEALEVEL 
SYSTEMS BEFORE RETURNED MERCHANDISE WILL BE 
ACCEPTED. AUTHORIZATION CAN BE OBTAINED BY CALLING 
SEALEVEL SYSTEMS AND REQUESTING A RETURN 
MERCHANDISE AUTHORIZATION (RMA) NUMBER. 

 

Sealevel Systems, Incorporated  
155 Technology Place 
P.O. Box 830 
Liberty, SC 29657 USA 
(864) 843-4343  FAX: (864) 843-3067 
www.sealevel.com 

email: support@sealevel.com 

 

Technical Support is available from 8 a.m. to 5 p.m. Eastern time.  

Monday - Friday 

 

Trademarks 

Sealevel Systems, Incorporated acknowledges that all trademarks referenced in 
this manual are the service mark, trademark, or registered trademark of the 
respective company. 
 

COMM+4.PCI 

is a trademark of Sealevel Systems, Incorporated. 

 

Summary of Contents for COMM+4.PCI




















Reviews: