background image

 

 

 

 

 

13 

© Sealevel Systems, Inc.  2104 Manual   |  SL9092  9/2021 

Appendix B 

 How To Get Assistance  

Please refer to Troubleshooting Guide prior to calling Technical Support. 

 

Begin  by  reading  through  the  Trouble  Shooting  Guide  in  Appendix  A.  If  assistance  is  still 
needed, please see below. 

 

When  calling  for  technical  assistance,  please  have  your  user  manual  and  current  adapter 
settings. If possible, please have the adapter installed in a computer ready to run diagnostics. 

 

Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many 
common questions. This section can be found at 

http://www.sealevel.com/faq.asp

.  

 

Sealevel  Systems  maintains  a  web  page  on  the  Internet.  Our  home  page  address 
is 

www.sealevel.com

The latest software updates, and newest manuals are available via our 

web site. 

 

Technical  support  is  available  Monday  to  Friday  from  8:00  a.m.  to  5:00  p.m.  eastern  time. 
Technical support can be reached at (864) 843-4343. 

 

 

RETURN  AUTHORIZATION  MUST  BE  OBTAINED  FROM  SEALEVEL  SYSTEMS  BEFORE  RETURNED 
MERCHANDISE  WILL  BE  ACCEPTED.  AUTHORIZATION  CAN  BE  OBTAINED  BY  CALLING  SEALEVEL 
SYSTEMS AND REQUESTING A RETURN MERCHANDISE AUTHORIZATION (RMA) NUMBER.

 

 

 

 

Summary of Contents for SEALINK+485I




















Reviews: