background image

 

 

 

 

 

18 

© Sealevel Systems, Inc.  2104 Manual   |  SL9092  9/2021 

Appendix G 

 Compliance Notices 

 

Federal Communications Commission (FCC) Statement 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  Class  A  digital 
device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in such case the user will be required to correct 
the interference at the 

user’s

 expense. 

EMC Directive Statement  

Products bearing the CE Label fulfill the requirements of the EMC directive (89/336/EEC) 
and of the low-voltage directive (73/23/EEC) issued by the European Commission. To 
obey these directives, the following European standards must be met: 

 

EN55022  Class  B

 - 

“Limits  and  methods  of  measurement  of  radio  interference 

characteristics of information technology equipment”

 

 

 

EN55024 

 

“Information  technology  equipment  Immunity  characteristics  Limits 

and methods of measurement”.

  

 

 

This is a Class B Product. In a domestic environment, this product may cause radio interference in 
which  case  the  user  may  be  required  to  take  adequate  measures  to  prevent  or  correct  the 
interference. 

 

 

 

 

Always use cabling provided with this product if possible. If no cable is provided or if an alternate 
cable  is  required,  use  high  quality  shielded  cabling  to  maintain  compliance  with  FCC/EMC 
directives. 

 

 

 

 

Summary of Contents for SEALINK+485I




















Reviews: