1. SAFETY
2. inTroducTion
3. SpEciFicATion
Original Language Version
AK98944 Issue: 1 - 08/04/14
© Jack Sealey Limited
WArninG!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this tool.
do noT
use the kit if any parts are damaged or missing as this may cause failure and/or personal injury.
Before each use, check the condition of the suction cups. Examine the rubber pads for excessive glaze, cuts or roughness.
If any component is worn or damaged replace immediately.
do noT
clean the suction cups with solvents or other harsh chemicals.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep the area free from unrelated materials and ensure that there is adequate lighting.
WArninG!
Always wear approved eye, face and hand protection when using this kit.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
Maintain correct balance and footing.
do noT
overreach, ensure the floor is not slippery, wear non-slip footwear.
Keep children and unauthorised persons away from the working area.
Ensure workpiece is secure before attaching the suction cups.
WArninG!
Ensure that the surface to which the suction cups are to be attached is non-pourous, clean, dry and free from
oil and grease.
do noT
exceed the maximum pull capacity of the kit.
do noT
use the kit for any purpose other than that for which it is designed.
do noT
use the kit when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use, store in a safe, dry, childproof location.
do noT
use any sharp object to loosen the suction cups as it may damage the rubber and prevent the tool from creating suction.
do noT
attempt to attach the suction cups to a person as severe bruising and/or damage to internal organs can occur.
do noT
allow anything to interfere with the free movement of the plunger whilst the suction cup is attached to a surface.
Keep fingers clear of suction release tag during use.
do noT
allow anything else to touch the release tab whilst in the process of lifting e.g. other lifting gear or adjacent
fixtures and fittings.
INSTRUCTIONS FOR:
WindScrEEn rEMoVAL/inSTALLATion TooL
MODEL No:
AK98944
IMPORTANT:
pLEASE rEAd THESE inSTrucTionS cArEFuLLY. noTE THE SAFE opErATionAL rEQuirEMEnTS, WArninGS & cAuTionS. uSE THE
producT corrEcTLY And WiTH cArE For THE purpoSE For WHicH iT iS inTEndEd. FAiLurE To do So MAY cAuSE dAMAGE And/or
pErSonAL inJurY And WiLL inVALidATE THE WArrAnTY. KEEp THESE inSTrucTionS SAFE For FuTurE uSE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
Designed for two man operation, with four pump action suction cups and lightweight frame. Provides control and accuracy when installing or
removing windscreens. Red line indicator warns of any vacuum loss.
Model no:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AK98944
Cup ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm
Maximum Lift Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100kg (Horizontal)
fig.1
