Tool Trolley wiTh 4 drawers & 2 door
cupboard
model no:
ap980mThv
Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFeTy
warNiNG!
ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this trolley.
warNiNG!
be careful to ensure that when closing the top you do not catch any part of your body in the lid or in the drawers.
9
Always load evenly with the centre of gravity of the load as near centre of the trolley as possible.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the trolley clean and tidy in accordance with good workshop practice.
9
Use the wheel locks to prevent the trolley from inadvertently moving.
9
Keep children and unauthorised persons away from the work area.
9
lock drawers and doors before moving.
8
do NoT
overload the trolley. max Capacity 160kg .
8
do NoT
use the trolley
for any purpose other than that for which it is designed.
8
do noT open more than one drawer at a time - unit may become unstable if multiple loaded drawers are open.
8
do NoT
stand on the trolley, use it as a ladder or allow others to ride on the trolley.
8
do NoT
leave unattended, especially when loaded, unless the wheels are locked, chocked or the trolley otherwise secured.
8
do NoT
use trolley on uneven ground and do not run over curbs or steps - use a ramp.
8
do NoT
use trolley if any part is significantly damaged, paying particular attention to the wheels.
NoTe!
lubricate top and bottom channels of drawer slides at least twice a year,
NoTe!
The assembly will require assistance.
2.
i
iNTroducTioN
Garage or workshop trolley with an overall weight capacity of 160kg.Top of the trolley is covered in tough composite with built-in
storage for small parts. Foldable side tray with 5kg weight capacity. Tool storage slots on the side to store more frequently used tools.
Internal locking system for added security, allowing drawers and cupboard to be locked separately. drawers are made to fit all
Sealey and Siegen tool box trays. Four drawers with liners and ball bearing slides, and a two door cupboard with magnetic doors.
Four bottom corners are fitted with bumpers to help prevent damage when moving around the workshop. Fitted with four wheels, two
fixed and two locking castors.
3.
i
speciFicaTioN
model no: ........................................................ AP980mTHV
overall size: (H x W x l) ...............................990 x 475 x 700
Total load capacity ...................................................... 160kg.
drawers ...............................................................................4
Cupboard .............................................................................1
Contents:
main storage compartment ..................................................1
C
astor - fixed
.......................................................................2
Castor - swivel .....................................................................2
Handle .................................................................................1
Flange nuts ........................................................................16
Cap screws ..........................................................................4
4. assembly
4.1.
Remove trolley from the box and unlock the trolley with the
keys attached. open the main storage area and remove all
parts, check contents against contents list, if any parts are
missing contact you local Sealey stockist immediately.
Close the storage area and drawers and lock before assembly.
4.2.
Attach castors to the bottom of the trolley using
4 flange nuts supplied.
4.3.
Attach side mounted handle to the right hand side of the cabinet using 4 bolts supplied.
NoTe:
The handle and the swivel castors should be mounted on the right hand side of the cabinet.
AP980mTHV Issue 1 08/08/18
Original Language Version
© Jack Sealey limited
Refer to
instruction
manual
