2. INTRODUCTION
All steel stand with pin and chain load support. All models manufactured to rigorous safety standards. Sold in pairs.
3. SPECIFICATION
Model No: .......................... AS3000.V3 ...............................AS5000.V2 ................................ AS5000M.V2
Capacity Each: ................... 2.5tonne (2,500 kg) ..................5tonne (5,000 kg). ..................... 5tonne (5,000 kg)
Capacity Pair: ..................... 5tonne (5,000 kg) .....................10tonne (10,000 kg) .................. 10tonne (10,000 kg)
Min. Height: ........................ 475mm ......................................385mm ...................................... 470mm
Max. Height: ....................... 705mm ......................................500mm ...................................... 700mm
Model No: .......................... AS7500.V2 ...............................AS10000 ................................... AS12000
Capacity Each: ................... 7.5tonne (7,500 kg) ..................10tonne (10,000 kg) .................. 12tonne (12,000 kg)
Capacity Pair: ..................... 15tonne (15,000 kg) .................20tonne (20,000 kg) .................. 24tonne (24,000 kg)
Min. Height: ........................ 490mm ......................................495mm ...................................... 525mm
Max. Height: ....................... 730mm ......................................735mm ...................................... 765mm
4. OPERATION
4.1.
Refer to vehicle manufacturer’s instructions for recommended support points.
4.2.
Check that the points are in good condition.
4.3.
Ensure the vehicle brake is on (or in park mode) and wheels are chocked.
4.4.
Adjust height of stand to correspond with the raised vehicle.
4.5.
Check that the locking pin is correctly pushed all the way through the centre
column and out of the other side, then position stands under vehicle at points
recommended by vehicle manufacturer.
4.6.
Lower the load onto stands carefully and slowly. Ensure the load bearing
points sit in the center of the stand saddle and check that the stands are stable.
IMPORTANT:
Ensure that there are no objects or persons that could impede
the safe lowering of the vehicle onto the stands.
4.7.
To remove stands jack vehicle slightly so that stand can be removed.
4.8.
After use, hold the centre column
(fig.1.1) firmly when removing the locking pin
(fig.1.3)
. Failure to do so will allow the center column to fall freely through the
main centre tube (fig.1.2) which could be dangerous.
WARNING!
Ensure you follow all instructions carefully. Failure to note these
warnings may cause damage, serious injury or loss of life.
4.9.
Before each use check to ensure stands and stand welds are not cracked,
and that there are no missing and/or damaged parts.
WARNING!
Any stand that appears to be damaged in any way must be
removed from service immediately.
5. MAINTENANCE
5.1.
Ensure the locking pins are in good order and condition.
5.2.
Owing to the potential hazards associated with these stands, do not misuse, or make
any modification to the stands or components.
5.3.
It is the responsibility of the stand’s owner to ensure the operator has read these instructions, and that the operator is familiar with
the stand’s use and limitations.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Original Language Version
© Jack Sealey Limited
fig.1
Parts support is available for this product. Please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500
AS3000.V3,AS5000.V2,AS5000M.V2,AS7500.V2,AS10000, AS12000 Issue 5 (H) 17/11/21
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
