A
UTOCHARGE15S | Issue 1 21/12/16
Original Language Version
© Jack sealey limited
4.1.10.
After full charge has been reached, disconnect the battery charger from the mains. then remove the chassis connection and then the
battery connection.
4.2.
charging out of Vehicle
4.2.1.
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE
(NEG, N, -) post.
4.2.2.
Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +) post of the battery.
8
Do not
face the battery when making the final connection.
4.2.3.
connect charger mains cable to an electrical outlet and switch on.
4.2.4.
charger light comes on.
4.2.5.
Charger automatically selects battery voltage and the appropriate light is lit. (A 24V battery may give the impression of a 12V battery. If
this is the case the charger will select the 12V option. The battery should be checked for faults.).
4.2.6.
The battery will be fully charged when the full LED is lit. Charging rate is displayed by the 6A, 10A, and 15A LED’s.
4.2.7.
After full charge has been reached, disconnect the battery charger from the mains.
4.2.8.
When disconnecting the charger, always do so in the reverse order of the connecting procedure.
4.2.9.
A marine (boat) battery must be removed and charged on shore. to charge it inboard requires equipment specially designed for marine
use.
5. maintenance
5.1.
cleaning and user maintenance should be carried out by competent persons.
5.2.
After use and before performing maintenance, unplug and disconnect the battery charger.
5.3.
use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery connectors, cords, and the charger case.
5.4.
ensure that all of the charger components are in place and in good working condition, for example, the plastic boots on the battery
clips.
5.5.
servicing does not require opening the unit, as there are no serviceable parts.
5.6.
All other servicing should be performed by qualified service personnel.
5.7.
If the mains cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons, in order to
avoid a hazard.
5.8.
store the charger unplugged, in an upright position.
5.9.
store inside, in a cool, dry place.
8
Do not
store the connectors clipped together, on or around metal, or clipped to cables. if the charger is moved around the shop or
transported to another location, take care to avoid/prevent damage to the cables,
connectors and charger. Failure to do so could result in personal injury or property damage.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
imPortant:
no liability is accepted for incorrect use of this product.
Warranty:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
sole uK distributor, sealey Group.
K
empson Way, Suffolk Business Park,
B
ury st. edmunds, suffolk.
i
P32 7AR
www.sealey.co.uk
sales@sealey.co.uk
01284 757500
01284 703534
environmental Protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
Parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
