3. SPECIFICATION
M
odel No:
................................................................. CP1210
Battery: ..............................12V 1.5-4Ah Li-ion (not included)
Brand: ......................................................................... Sealey
D
isc Size:
.................................................................. Ø76mm
Free Speed: ...........................................................18500rpm
Motor Power:.................................................................200W
Replacement Parts: ...................... CP1200BP - Battery Pack
S
pindle Size:
..................................................................... M5
Vibration/Uncertainty: .....................1.23 (m/s^2) / 1.5 (m/s^2)
4. ASSEMBLY
4.1.
ATTACHING A GRINDING/CUTTING DISC
NOTE:
Discs should only be fitted by a person holding a grinding wheel certificate.
4.1.1.
Place the grinding (or cutting) disc over the spindle and onto the clamping flange.
4.1.2.
When using flat cutting discs, screw the disc retaining flange nut onto the spindle.
4.1.3.
Stop the spindle from turning by pushing in and holding down the spindle lock button (fig.1).
4.1.4.
Lock the grinding/cutting disc into place by tightening the disc retaining flange nut with the supplied Allen key.
4.1.5.
When complete, release the locking button and check that it has sprung back to its initial position.
5. OPERATION
WARNING!
Ensure you have removed the battery from the grinder before changing accessories.
5.1.
PREPARATION
5.1.1.
Ensure the cutting disc and safety guard are securely fitted and correctly positioned.
5.1.2.
Re-attach battery.
WARNING!
When the grinder first starts it will kick. You must ensure, therefore, that the tool is securely gripped in both hands.
WARNING!
Before use, ensure that you are wearing approved safety goggles, ear defenders, appropriate dust mask if dust will
be generated and safety gloves, and that all other safety instructions in Section 1 are followed carefully.
5.2.
ON/OFF CONTROL (fig.1)
5.2.1.
The ON/OFF switch is designed to avoid accidental starting.
5.2.2.
Once the battery is plugged in start the grinder by pushing the switch (fig.1) forward and down.
5.2.3.
To stop the machine press the bottom of the switch.
5.2.4.
If the power to the grinder is fails whilst in use release the switch and remove the battery from the grinder.
DO NOT
reconnect the
battery until you are sure that the power has been restored.
5.3.
GRINDING HEAD ALIGNMENT
5.3.1.
Rotate the grinding head until you can depress the spindle locking button (fig.1) and twist the head to the required position. Ensure
the disc is correctly mounted and secure before turning the power on.
5.4.
CUTTING
5.4.1.
The key to effective operating is controlling the pressure and surface contact between the disc and the work piece.
WARNING!
DO NOT
switch the grinder on whilst the disc is in contact with the work piece. Bring the rotating disc to the work piece.
5.4.2.
Allow the disc to reach full speed before starting to cut.
5.4.3.
When cutting is complete allow the work piece to cool.
DO NOT
touch the hot surface.
5.4.4.
Remove the battery from the grinder from the mains power supply, clean and store in a safe, dry, childproof area.
6. CUTTING DISCS
WARNING!
DO NOT
USE DISCS THAT ARE DAMAGED, OR SUSPECTED TO BE DAMAGED.
6.1.
Before using a grinding/cutting disc ensure that there are no fissures or cracks. Once mounted on the grinder, test the disc before
use by facing the grinder in a safe direction (point away from yourself, others and vulnerable items) and run for a short time.
▲
DANGER
! Use of damaged discs is dangerous and may cause personal injury.
6.2.
Grinding and cutting discs used in association with this machine shall be of an adequate speed rating and be suitable for the job in
hand. Only persons holding a grinding wheel certificate are authorised to change grinding discs. Ensure that the speed rating on
the disc is equal to, or higher than, that of the grinder.
fig.1
CP1210 Issue 1 16/07/2020
Original Language Version
© Jack Sealey Limited
