CORDLESS LITHIUM-ION ANGLE GRINDER
Ø115MM 20V 1HR CHARGE
MODEL NO:
CP20VAGB
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Disconnect the battery from the grinder unit before changing accessories, servicing or performing any maintenance.
9
Maintain the grinder and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the grinder is switched off before installing the battery.
9
Keep the grinder battery and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the grinder e.g. ceiling, floors and enclosures may contain electrical items or water piping.
9
Ensure battery is correctly inserted into the grinder handle and latched in place before attempting to switch on.
9
Secure loose workpieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this grinder does not need to be plugged into the mains power.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the grinder where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the grinder.
8
DO NOT
operate the grinder if any parts are missing as this may cause failure or possible personal injury.
8
DO NOT
hold unsecured workpiece in your hand.
8
DO NOT
carry the grinder with your finger on the power trigger.
8
DO NOT
use the grinder for a task it is not designed to perform.
8
DO NOT
operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the grinder, battery or charger wet or use in damp or wet locations.
9
Keep the grinder, battery and charger in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
2. INTRODUCTION
T
he 20V Series has been designed to suit the DIY enthusiast or the professional. These body only tools offer a one battery fits all solution with a
choice of 20V lithium batteries ranging from 2Ah to 6Ah, meaning costs can be kept down whilst quality remains high. Quality, stylish, lightweight
tools with composite housing and a soft grip making them comfortable and easy to use.
3. SPECIFICATION
Model No: .............................................................CP20VAGB
Battery:
2Ah ...................................................................... CP20VBP2
4Ah ...................................................................... CP20VBP4
6Ah ...................................................................... CP20VBP6
Disc Size: .................................................................Ø115mm
Spindle Size: ....................................................... M14 x 2mm
Motor Power: .................................................................700W
No Load Speed: .................................................... 10,000rpm
Replacement parts ......................Mains charger - CP20VMC
Noise Power: ............................................................94.8dB.A
Noise Pressure: .......................................................83.8dB.A
Vibration: ............................................................... 6.151m/s
2
Vibration uncertainty: ................................................. 1.5m/s
2
4. WHEEL / DISC FITTING
NOTE-:
Remove battery to avoid accidental starting.
4.1.
Clamp the wheel guard to the neck of the grinder.
The orientation can be changed to suit the task later.
4.2.
Fit the side auxiliary handle to the user preferred side.
CP20VAGB Issue 1 22/12/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Wear a mask
