background image

4.  ASSEMBLY

4.1. 

  

 Assemble all parts before filling with fuel and oil.

4.2.    

Wheels see figs 6-9

4.3. 

   

To mount the wheels, first slide the axle through the mountings on the bottom of the generator and fit the wheels as shown in fig.7.  

 

Make sure that the sides of the wheels with the more protruding wheel hubs are facing towards the generator, as the wheels will    

 

otherwise drag against the frame.

4.4. 

  

Foot see fig.6

4.4.1.   

Bolt feet, one each side, to frame at the opposite end from the axle (16).

4.5.    

Handle see

 

figs 8 & 9

4.5.1. 

  

Bolt brackets (17) to frame. Bolt handle (18) to brackets, see fig.9. 

 

5.    SET UP

5.1.    

Electrical safety

5.1.1.   

Electric supply cables and connected equipment must be in perfect condition.

5.1.2. 

    The generator is to be operated only with equipment whose voltage specifications conform with the generator’s output voltage.

5.1.3.     Never connect the generator to mains power supply.

5.1.4.   

Keep the cable length to the connected equipment as short as possible.

5.2.    

Earth connection

5.2.1.   

The housing is required to be connected to earth in order to discharge static electricity. To do this, connect one end of a cable to the  

 

earth connection on the generator, see fig.3.4 and the other end to an external earth (for example an earthing rod).

6.  OPERATION

 

Important: You must fill up with engine oil (approx.1.1ltr) and fuel before you can start the engine. See 7.4 and fig.10.

 

Oil shortage light will illuminate if engine oil is low, see fig.3.9A.

6.1. 

    

Make sure that the generator has sufficient ventilation.

6.2.     

Make sure that the ignition cable is secured to the spark plug.

6.3.     

Inspect the immediate vicinity of the generator.

6.4.     

Disconnect any electrical equipment which may already be connected to the generator. 

6.5.    

Starting the engine

6.5.1. 

  

Open the petrol tap, see fig.2.13 by turning it down.

6.5.2. 

   

Move the ON/OFF switch, see fig.1.10 to the ON position.

6.5.3. 

   

Move the choke lever, fig.1.11 to position IØI.

6.5.4. 

    Start the engine with the recoil starter, see fig.2.12 by pulling the handle forcefully. If the engine does not start, pull the handle again.

6.5.5. 

    Push the choke lever, see fig.2.11 back again after the engine has started.

 

‰

  

WARNING!

 When starting with the recoil starter, the motor may recoil suddenly as it starts up, resulting in hand injuries. Wear    

  protective gloves when starting the equipment.

6.6.    

Connecting equipment to the generator

6.6.1.   

230V socket

 Connect the equipment you want to use to the 230 V~socket, see fig.1.3A.

G3801 | Issue 1- 24/06/16

Original Language Version

© Jack Sealey Limited

12

13

14

Summary of Contents for G3801






Reviews: