sealey group, kempson Way, suffolk Business park, Bury st edmunds, suffolk. ip32 7ar
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
environMent protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee reguLations
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid
waste authority for recycling information.
note
: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: no liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
5.8.
Muffler screen and spark arrester.
Warning!
The engine and muffler will be very hot after the engine has been run. Avoid touching the engine and muffler while they
are still hot.
5.8.1.
loosen the cover and remove.
5.8.2.
Loosen the bolts then remove the muffler cap, the muffler screen and spark arrester.
5.8.3.
Clean the carbon deposits on the muffler screen and spark arrester using a wire brush.
Brush gently to avoid damage to the component.
5.8.4.
Check the muffler screen and spark arrester. Replace if damaged.
5.8.5.
install the spark arrester.
5.8.6.
Install the muffler screen and the muffler cap.
5.8.7.
install the cover and tighten the screws.
5.9.
Fuel tank filter
5.9.1.
Remove the tank cap and filter.
5.9.2.
Clean the filter with petrol.
5.9.3.
Wipe the filter and install it.
5.9.4.
replace the fuel tank cap. Be sure the fuel tank cap is tightened securely.
5.10.
fuel filter
5.10.1. t
he fuel filter is located in the fuel pipe leading from the fuel tank to the carburettor.
5.10.2. drain fuel from fuel tank.
5.10.3. s
queeze the pipe clamps and remove the filter.
5.10.4.
r
eplace the filter.
5.10.5. Attach the fuel pipes and re-clamp.
5.10.6. check for any fuel leaks.
6.
storage
long term storage of the generator will require preventive procedures to guard against deterioration.
6.1.
turn the engine switch to “stoP”.
6.2.
Remove fuel tank cap and filter.
6.3.
Extract the fuel from the tank into an approved fuel container. Replace the fuel filter and cap.
6.4.
Wipe off any spilt fuel.
6.5.
start the engine and leave it to stop. (approx 20 min)
6.6.
Drain the fuel from the carburettor, by removing screw on the float chamber. Replace screw.
6.7.
turn the engine switch to “stoP”.
6.8.
remove the spark plug, pour about one table-spoon of sAe 10W-30 into spark plug hole. using the recoil starter turn over the engine
to coat the cylinder walls with oil.
6.9.
replace spark plug, pull the recoil starter until you feel compression. then stop pulling. (this prevents the cylinder and valves from
rusting)
6.10.
clean exterior of the generator with a dry cloth. store the generator in a dry, well-ventilated child proof area.
7. trouBLeshooting
7.1.
fuel system:- check fuel in tank, vent knob and fuel tap to “on”
Check fuel filter, carburettor, clean as required.
7.2.
Oil System:- Check oil level, fill as required.
7.3.
electrical system:- check/clean spark plug
faulty ignition system, consult our authorized stockist.
7.4.
no power produced:- Press the dc protector to “on”
the Ac pilot light (green) goes off, stop the engine and then restart.
G
I2300,GI3500 Issue 2 (fig1) 19/04/18
Original Language Version
© Jack sealey limited
