NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
7. TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
CORRECTIVE ACTION
Engine does not start.
Throttle settings
Empty fuel tank
Spark plug gap is incorrect
Spark plug loose or defective
HT lead loose or disconnected
Carburetor is flooded with fuel
Air filter element is clogged
Faulty ignition module
Contact Authorised Service Agent
Refill with grade 95RON non leaded petrol
Gap required to be 0.7mm to 0.8mm
Remove plug, clean, refit or replace
(torque 20Nm)
Check HT lead connected correctly
Remove air filter element and pull recoil cord
continuously until the carburetor clears. Replace
filter.
Fit new filter element.
Contact Authorised Service Agent
Engine difficult to start or runs erratically, loses
power, poor idling
Contaminated fuel
Vent hole blocked in filler cap
Air filter element clogged
Defective spark plug or gap is incorrect
Air way slots in motor shroud are blocked, cooling
fins and air passages under engine blower housing
are blocked.
Drain fuel tank and clean. Refill with fresh fuel.
Clean and refit.
Fit new filter element.
Remove plug, set gap refit or fit new plug
(torque 20Nm)
Remove debris from associated parts and improve
cleaning regime.
Engine skips at full speed
Spark plug gap too close
Gap required to be 0.7mm to 0.8mm.
Engine overheats
Cooling air flow is restricted
Incorrect spark plug fitted
Remove debris from all cooling air flow passages
and improve cleaning and maintenance regime.
Fit new correct spark plug with correct gap.
Mower vibrates abnormally
Blade fixing has worked loose
Blade is damaged affecting symmetry
Stop engine immediately.
Tighten blade, tightening torque approximately
30Nm.
Repair to have equal form and weight about the
centre bolt or replace with a genuine spare part.
Poor grass collection
Blade condition
Grass box full
Airflow interrupted
Engine not running at full speed with no load
If damaged repair or replace.
Note!
Maintenance of
the blade is best done by a specialist with the
appropriate tools. Wear tough gloves when
removing or fitting.
Empty grassbox.
Clear accumulated grass from all areas including
cutter deck and engine vent slots.
This can only be checked/repaired by qualified
personnel, contact Authorised Service Agent.
SEE ALSO ENGINE MANUFACTURERS MANUAL
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
GL112 Issue No: 1 -15/04/15
Original Language Version
© Jack Sealey Limited
Warning! Danger!
Keep others away at least 10 metres.
Caution, blade will continue to rotate after the motor
has been switched off.
DO NOT
leave device in the rain.
DO NOT
work in the rain
Keep others away from the danger area.
Caution, rotating blade. Keep feet and hands away.
