Infrared quartz patIo heater
2000W/230V WIth telescopIc stand
Model no:
Ifsh2003
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
note: only use outdoors or in well ventilated surroundings.
1. safetY
1.1.
electrIcal safetY
WarnInG!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct
fuse - see fuse rating in these instructions.
8
do not
pull or carry the appliance by the power cable.
8
do not
pull the plug from the socket by the cable.
8
do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
replaced
immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
General safetY
WarnInG!
Ensure the heater is at least 1m from any object, 30cm from the ceiling and we recommend 1.8m from floor level.
9
The unit must be placed on a horizontal flat surface.
9
Familiarise yourself with the applications and limitations of the heater.
9
ensure the heater is in good order and condition before use. If in any doubt do not use the unit and contact your Sealey dealer.
9
Only use recommended attachments and parts. Using unauthorised parts maybe dangerous and will invalidate your warranty.
9
Check that element guards are in place, undamaged and firmly attached.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
disconnect from mains and allow to cool before moving or attempting any cleaning or maintenance.
8
do not
use this heater with timers or other devices which switch the heater on automatically.
8
do not
get the heater wet or use in damp or wet locations or areas where there is condensation.
8
do not
locate the heater below the power outlet.
8
do not
move the heater whilst in operation or even when still warm.
8
do not
locate the heater in an area where there are flammable gases, dust etc.
8
do not
dismantle the heater for any reason. The heater must be checked by qualified personnel only.
8
do not
use this product to perform a task for which it has not been designed.
WarnInG!
If a fuse blows, ensure it is replaced with an identical fuse type and rating.
9
When not in use, store the heater carefully in a safe, dry, childproof location.
WarnInG!
Never touch the element glass directly with fingers. Use a soft cloth, otherwise the tube may get damaged.
WarnInG!
Two dark points may exist on the surface of the heating element, or the surface of the heating element may turn white
during the first few minutes of operation. This is normal and will not affect the performance of the heater.
9
Children of less than 3 years and less than 8 years should be kept away from the heater unless constantly supervised.
Recommended fuse rating
13 Amp
I
FSH2003 | Issue:5 (ERP) 23/08/18
Original Language Version
© Jack Sealey limited
Refer to
instruction
manual
