p
p
WARNING! Ensure you read, understand and apply the safety instructions before use.
p
p
WARNING! Before use, ensure the motorcycle to be lifted has a suitable structure and centre of gravity to accommodate the
lift saddle without damaging the bike.
DO NOT use if the lift will foul on the exhaust or other vulnerable parts. Remove any lower fairing and ensure the bike is
adequately strapped to the lift before operating.
4.1. Position the bike in a suitable area, checking that the surface on which the lift will stand is solid and flat (preferably concrete). Ensure that
there is good access and clearance beneath the bike for the lift to be wheeled under.
4.2. Wheel lift under bike so that the centre of gravity of the bike is over the saddle (36), which must fit snugly against the underside of bike.
4.3. By depressing the lift pedal (21), raise the saddle up to the underside of the bike.
4.4. Secure the bike to the saddle with suitable straps, ensuring that the bike will not move once the lift is in operation.
4.5. Screw down the two locking bolts (15) to just lift the castors off the ground. This will ensure that the lift does not move during use.
4.6. Pump the lift pedal (21) to raise the load.
4.7. When the lift is fully raised engage the stop bar (28) with the tabs on the frame so that the lift cannot be inadvertently lowered.
4.8. When work is complete, check under the lift to ensure that there are no obstructions and that it is safe to lower the unit.
Disengage the safety bar from the frame tabs and then
SLOWLY
press the foot pedal (17) to
GENTLY
lower the lift.
Q
IMPORTANT:
Speed of lowering is controlled by the hydraulic jack. The more the valve is opened the more rapidly the lift descends.
Ensure the descent is slow and controlled.
4.9. When the lift is fully lowered, ensure the bike is on its wheels and supported in the upright position. Unstrap the bike from the lift, raise
the side tilt screws, and move the lift from under the bike.
4. OPERATING INSTRUCTIONS
5.1.
When the lift is not in use, it must be stored in the lowest position to minimise ram and piston corrosion.
5.2.
Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts with acid free oil.
5.3.
Before each use check all parts. If any part of the lift is damaged or suspect remove lift from service and take necessary action to repair.
DO NOT
use the lift if it is believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
5.4.
Periodically check the ram and piston for signs of corrosion. Clean exposed areas with a clean oiled cloth.
5.5.
The hydraulic oil level is checked as follows:
1) Position the fully lowered lift on a level surface.
2) Remove filler plug. Correct oil level is to filler hole - add hydraulic jack oil as necessary.
p
WARNING! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC JACK OIL, must be used. DO NOT use brake fluid.
Q
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair. Contact your authorised dealer.
5. MAINTENANCE
6. DECLARATION OF CONFORMITY
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE LIFT.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN THE PRODUCT TO US.
Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning product
Should the lift become completely unserviceable, draw off the oil into an approved container and dispose of the lift and the oil according to
local regulations.
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is
in conformity with the following standards and directives.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
680KG MOTORCYCLE & QUADBIKE LIFT
Model: MC402.V2
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
29 September 2005
Signed by Mark Sweetman
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor,
Sealey Group
, Bury St. Edmunds, Suffolk.
MC402.V2 - 290905
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
01284 703534
Web
