INSTRUCTIONS FOR:
450KG HYDRAULIC MOTORCYCLE LIFT
MODEL No:
MC455.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. SPECIFICATION
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Capacity . . . . . . . . . . . . . . . . . . . . . . . 450kg Width. . . . . . . . . . . . . . . . . . . . . . . . 500mm
Minimum Height . . . . . . . . . . . . . . . .150mm Length. . . . . . . . . . . . . . . . . . . . . . 2210mm
Maximum Height . . . . . . . . . . . . . . .600mm
Maximum Load Length . . . . . . . . . 1820mm
Steel construction heavy-duty hydraulic pump and ram assembly. Fitted with platform safety locking device with four height settings of 600mm,
530mm, 440mm and 320mm to prevent accidental lowering. Supplied with full width loading ramp and adjustable front wheel clamp. Base frame
fitted with transport wheels and lock-down bolts to prevent lift from moving during use. Suitable only for motorcycles with a centre stand.
WARNING! THIS LIFT IS ONLY SUITABLE FOR MOTORCYCLES WHICH HAVE A CENTRE STAND.
WARNING! Ensure the bike is adequately strapped onto the platform before operating.
Maintain the
lift in good condition (use an authorised service agent).
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use a qualified person to lubricate and maintain the lift.
DO NOT
use brake fluid to top up hydraulic unit.
Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike.
DO NOT
operate the lift
on tarmacadam, as the surface may be unstable.
Keep the lift clean for best and safest performance.
The maximum bike weight is 450kg.
DO NOT
exceed this rated capacity.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
Maintain correct balance and footing, do not overreach. Ensure the floor is not slippery and wear non-slip shoes.
Ensure the bike is adequately secured to the lifting platform with appropriate straps.
Before lifting check that there are no overhead obstructions.
When platform has been raised to the working height ensure the locking bar is engaged to prevent accidental lowering.
Keep children and unauthorised persons away from the work area.
The lowering speed will vary according to the weight of the load and the amount by which the release pedal is depressed.
DO NOT
use the lift for a task it is not designed to perform.
DO NOT
use MC455
to lift persons.
DO NOT
operate the lift if damaged.
DO NOT
exceed the rated capacity of the lift.
DO NOT
operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
allow untrained persons to operate the lift.
DO NOT
attempt to transport a load on the lift. The lift must only be used in a static position for raising and lowering loads.
DO NOT
make any modifications to the lift and
DO NOT
adjust or tamper with the safety valve.
Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
Original Language Version
MC455.V2 Issue: 1 - 10/06/13
© Jack Sealey Limited
