4. CHARGING INSTRUCTIONS
WARNING! YOU MUST FOLLOW SAFETY INSTRUCTIONS
IMPORTANT
Charge RoadStart for 72 hours immediately after purchase. After each use connect the charger to the Roadstart in order
to charge and maintain the internal battery. The intelligent charger will monitor and maintain the Roadstart battery indefinitely. Never
wait until the RoadStart is completely discharged before recharging.
4.1.
Read the entire manual before using this product. Failure to do so could result in serious injury or death.
4.2
.
This charger is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the charger by a person
responsible for their safety.
4.3.
Children should be supervised to ensure they do not play with the charger.
WARNING
RISK OF EXPLOSIVE GASES. PREVENT FLAMES AND SPARKS. PROVIDE ADEQUATE VENTILATION DURING
CHARGING.
4.4.
The charger and RoadStart must be placed in a well-ventilated area during use.
4.5.
Make sure to place the charger on a dry, non-flammable surface, such as metal or concrete.
4.6.
To reduce the risk of a battery explosion, follow these instructions and those published by the battery manufacturer and the
manufacturer of any equipment you intend to use in the vicinity of the battery. Review the cautionary markings on these products and
on the engine.
4.7.
Digital Display on the RoadStart
To check the internal battery’s charge status, either press the Battery Status button to get the percent of charge or turn the ON/OFF
switch to the ON position to get the battery voltage. Charge the internal battery if the display shows it is under 100%. When connected
to the vehicle, the display shows the vehicle’s battery voltage. When connected and in the ON position, the display shows the
equalized voltage between the vehicle’s battery and the internal battery.
NOTE: The internal battery’s charge status is most accurate when the RoadStart has been disconnected from all devices and charging
sources for a few hours.
4.8.
LED Indicators on the Charger
CHECK BATTERY
(red) LED lit:
Indicates that the charger is not properly connected to the Roadstart. If the charger does not
detect a properly connected battery, the CHECK BATTERY LED will light. Charging will not begin if the CHECK BATTERY LED is on.
CHECK BATTERY
(red) LED flashing:
Indicates the charger is in abort mode. If charging cannot be completed normally,
charging will abort. When charging aborts, the charger's output is shut off and the CHECK BATTERY LED will flash. To reset after an
aborted charge, unplug the charger from the AC outlet, wait a few moments and plug it back in.
CHARGING (amber) LED lit:
Indicates the charger has detected a battery and is charging it. After the battery is fully charged,
the charger will automatically go into maintain mode and maintain it at full charge without damaging it.
CHARGED (green) LED lit:
Indicates the battery is fully charged and the charger is in maintain mode. When the CHARGED LED
is lit, the charger has started Maintain Mode. In this mode, the charger keeps the battery fully charged by delivering a small current
when necessary. NOTE: The maintain mode technology utilized in Sealey chargers allows you to safely charge and maintain a
healthy battery for extended periods of time. However, problems with the battery, electrical problems in the RoadStart, improper
connections or other unanticipated conditions could cause excessive current draws. As such, occasionally monitoring your battery and
the charging process is recommended.
NOTE:
Even if the digital display is showing 100%, the internal battery is not fully charged until
the LED on the charger shows green.
4.9.
Charging the RoadStart's Internal Battery using the Included Charger
IMPORTANT
Only use the charger that was included with the RoadStart to charge the internal battery. Using any other charger or
using the included charger for any other purpose could result in personal injury or property damage.
(Refer to charger safety instructions in Section 1.3)
4.10.
Charging
4.10.1. To charge, plug the included charger into the charger plug on the side of the RoadStart.
4.10.2. Plug the charger into an electrical wall outlet, ensuring that the input voltage matches that required by the charger. Make sure to place
the charger on a dry, nonflammable surface like metal or concrete.
4.10.3. While the RoadStart is charging, the CHARGING LED will light on the charger. Complete charging may take up to 24 hours.
The RoadStart is then ready to use.
4.10.4. After charging disconnect the charger from the supply mains. Then remove all connections to the RoadStart.
5. OPERATION
5.1.
Jump Starting a Vehicle Engine
I
MPORTANT:
DO NOT
use the RoadStart while charging the internal battery.
5.1.1. Turn the vehicle’s ignition OFF before making cable connections.
5.1.2. Connect the RoadStart to the vehicle’s battery, positive (red) first, then negative (black) should be connected to an earth on the chassis.
If you have connected the clamps incorrectly, an audio alarm will sound.
DO NOT
turn the RoadStart ON/OFF switch to the ON position.
This could cause serious damage to the RoadStart or the vehicle. Reverse the connections and the audio alarm will stop.
5.1.3. Turn the RoadStart ON/OFF switch to the ON position.
5.1.4. Crank the engine. If the engine does not start within 3-8 seconds, stop cranking and wait at least 1 minute before attempting to start the
vehicle again, (this permits the RoadStart battery to cool down).
5.1.5. After the engine starts, turn the RoadStart ON/OFF switch to the OFF position, within 15 seconds.
NOTE:
If the vehicle's charging system is allowed to continue to charge the RoadStart's internal battery, the audible warning system will
operate if the battery reaches 15V - immediately disconnect as below to prevent damage.
5.1.6. Disconnect the RoadStart from the vehicle, negative (black) first, then the positive (red) clamp. Return the battery clamps to their
storage holders and recharge the RoadStart.
5.1.7. When using the other features of the RoadStart, always observe the following steps:
5.1.8. Ensure the battery clamps are securely clipped in the storage holders.
5.1.9. Charge the RoadStart as soon as possible after using.
IMPORTANT
An audible warning will sound if:
- the clamps are incorrectly connected
- PBI4424S if 24V is selected
- if RoadStart is connected to a 24V vehicle, and 12V is selected.
PBI2212S,PBI3612S,PBI3624S,PBI4424S Issue: 1 - 06/05/14
Original Language Version
© Jack Sealey Ltd
