3.1 ASSEMBLY
3.1.1
The jack comprises the following parts:
Steel chassis.
Two-part pumping handle with M6x35 bolt.
3.1.2
Insert the upper handle into the lower handle. Secure the
two pieces together with the bolt (A). (Fig.1).
3.1.3
Undo the handle socket screw (B) until it no longer
protrudes into the handle socket (Fig.2).
3.1.4
Insert the pump handle into the handle socket hole,
engaging the hexagonal drive of the release valve.
3.1.5
Ensure that the handle is correctly inserted into the socket,
then tighten the handle socket screw (B).
INSTRUCTIONS FOR:
TROLLEY JACK 3TONNE
LOW ENTRY
MODEL No:
3075LE
Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/
OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY PRECAUTIONS
2. INTRODUCTION / SPECIFICATION
3. ASSEMBLY
Ensure the jack is in sound condition and good working order.
Take action for immediate repair or replacement of damaged
parts.
Use genuine parts only. The use of improper parts may be
dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
Keep working area clean and tidy and free from unrelated
materials.
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in
.
Chock wheels of vehicle
.
Ensure the vehicle handbrake is engaged, engine is switched off
and transmission is in gear (or “PARK” if automatic).
Ensure minimum distance of 0.5m between vehicle and static
objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the
jack is in use.
Ensure there are no passengers in the vehicle.
Place jack under only those lifting points recommended by
vehicle manufacturer
(see vehicle handbook).
Check that the lifting point is stable and centred on the jack
saddle.
Ensure the jack wheels are free to move and that there are no
obstructions.
DANGER: Use the jack for lifting only, NOT for supporting the
lifted load.
Ensure there are no persons or obstructions beneath the vehicle
before lowering.
Use suitable axle stands under the vehicle before proceeding with
any task.
Use a qualified person to lubricate and maintain the jack.
Ensure that only
hydraulic jack oil
is used in the jack.
DO NOT
operate the jack if damaged.
DO NOT
allow untrained persons to operate the jack.
DO NOT
exceed the rated capacity of the jack.
DO NOT
allow the vehicle to move during lifting or lowering, or
use the jack to move the vehicle.
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery
acid, or other dangerous substances.
DO NOT
work under the vehicle until appropriately rated axle
stands have been correctly positioned.
DO NOT
use the jack for purposes other than that for which it is
intended.
DO NOT
top up hydraulic system with brake fluid. Use hydraulic
jack oil only. (Sealey Part No: HJO500MLS or HJO5LS)
DO NOT
adjust the safety overload valve.
When not in use store jack, fully lowered, in a safe, dry, childproof
location.
Model No: ........................................................................ 3075LE
Capacity ............................................................................ 3tonne
Minimum saddle height ..................................................... 95mm
Maximum saddle height .................................................... 540mm
Maximum chassis height .................................................. 135mm
Length ............................................................................... 685mm
Weight ............................................................................... 44.5kg
4. HYDRAULIC SYSTEM PURGING
4.1
Open the release valve by turning it two full turns
counter-clockwise.
4.2
Pump the handle a minimum ten full strokes.
4.3
Close the release valve by turning it clockwise.
Twin piston 'Rocket Lift' feature brings lifting arm straight into contact
with the jacking point in 1-2 strokes. Universal joint release
mechanism allows safer, more controlled lowering of the jack.
Profiled lifting arm gives low clearance height of just 95mm x 390mm
deep making this unit suitable for sports and custom cars. Heavy-duty
chassis with strengthening flanges along the top edge for extra
torsional rigidity under load. Fitted with heavy-duty one-piece
hydraulic unit with pump-through action preventing handle locking at
maximum ram extension. Large sized saddle aids positioning under
vehicle and safety valve prevents overloading. Supplied with foam
jacking sleeve to prevent damage to vehicles bodywork and integral
saddle pad.
Original Language Version
3075LE Issue: 1 - 16/07911
Fig.2
Fig.1
