WARNING!
Ensure all preliminary checks are carefully carried out before use of jack. Immediately repair or replace damaged
parts (use authorised service agent). Ensure use of
genuine parts only. Non authorised parts may be dangerous and will
invalidate the warranty.
WARNING!
Use jack on level and solid ground, preferably concrete. Ensure the floor over which the jack will be transported is swept clean.
DANGER!
DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious personal or fatal injury may
result.
Use jack in an adequate working area for its function, keep area clean, tidy and free from unrelated materials. Ensure there is adequate
lighting.
Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Remove ill fitting clothing, ties, watches, rings, and other loose jewellery, contain or tie back long hair.
WARNING!
Ensure load is placed level and centrally on jack saddle and load is fixed in place before attempting to lift, lower, or transport.
The lowering speed will vary according to the weight of the load and the release valve setting.
Ensure the jack saddle is fully lowered and is clean, dry, and oil free before attempting to transport the jack with or without a load.
Fix load with support chain provided, do not substitute an inferior form of restraint for the support chain.
Diligence is required in ensuring that you continually monitor the operation until completed.
Should the jack omit any abnormal sounds during use STOP immediately and contact your local service agent.
DANGER! If jack tips or leans STOp whAT yOuR ARE DOING. MOVE QuICKLy TO A SAFE DISTANCE. DO NOT TRy TO hOLD
OR STEADy JACK. Serious personal or fatal injury may result.
WARNING! DO NOT
operate jack if any parts are damaged or missing .
DO NOT
exceed the rated capacity of the jack.
DO NOT
allow untrained persons to operate the jack.
DO NOT
place any part of your body within or under the jack during use.
DO NOT
raise or lower vehicle lifting platform whilst the transmission jack is being used.
DO NOT
transport the jack, with or without a load, with the saddle in the raised position.
DO NOT
get jack wet or use in damp or wet locations or areas where there is condensation.
DO NOT
operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT
lift or support vehicles with jack and do not use jack as a load sustaining device.
DO NOT
use jack for any purpose other than removal, transportation and installation of transmissions.
DO NOT
use jack without support chain or substitute an inferior form of restraint for the chain.
DO NOT
make any modifications to the jack, and DO NOT adjust or tamper with safety valve.
DO NOT
remove any labels from the jack. If labels are damaged or unclear replace them.
Use a qualified person to lubricate and maintain the jack. DO NOT use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
Before storing in safe area, ensure all parts are clean, free of grease and oil (especially saddle). Lower saddle to the lowest position.
INSTRUcTIONS FOR:
TRANSMISSION
JACK YANKEE 1TONNE/1.5 TONNE FLOOR
Model No's:
TJ1000F, TJ1500F
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMpORTANT!
ENSURE YOU READ AND UNDERSTAND THESE INSTRUCTIONS FULLY BEFORE ATTEMPTING TO USE THE JACK. NOTE
THE SAFE OPERATIONAL REQUIREMENTS, DANGERS, WARNINGS & CAUTIONS. USE THE JACK CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED.
wARNING!
FAILURE TO APPLY THESE INSTRUCTIONS MAY CAUSE
DAMAGE, SERIOuS
pERSONAL OR FATAL INJuRy.
FAILING TO FOLLOW INSTRUCTIONS WILL ALSO INVALIDATE YOUR WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATIONS
Precision valve allows delicate adjustment when removing gearbox and realigning during replacement. Includes two chains for safe loading.
Supplied with pulling hook and four castors for extra manoeuvrability in confined spaces. Fully adjustable saddle with forward and backward tilt.
SPECIFICATIONS:
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ1000F. . . . . . . . . . . . . . . TJ1500F
Rated capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . 1000kg. . . . . . . . . . . . . . . . .1500kg
Maximum Saddle Base Height: . . . . . . . . . . . . . . 730mm. . . . . . . . . . . . . . . . .810mm
Minimum Saddle Base Height:. . . . . . . . . . . . . . . 185mm. . . . . . . . . . . . . . . . .170mm
Saddle Forward Tilt Angle: . . . . . . . . . . . . . . . . . . . . . 60°. . . . . . . . . . . . . . . . . . . . 70°
Saddle Backward Tilt Angle:. . . . . . . . . . . . . . . . . . . . 20°. . . . . . . . . . . . . . . . . . . . 28°
chassis Length/Width: . . . . . . . . . . . . . . . . . 850/495mm. . . . . . . . . . . . . 895/500mm
Saddle Length/Width: . . . . . . . . . . . . . . . . . . 200/180mm. . . . . . . . . . . . . 250/200mm
Saddle Lateral Travel: . . . . . . . . . . . . . . . . . . . . . . 65mm. . . . . . . . . . . . . . . . . .90mm
Saddle Pivot: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360°. . . . . . . . . . . . . . . . . . . 360°
NOTE: The use of symbols in this document is to attract your attention to possible danger. The symbols and warnings themselves do not eliminate any danger,
nor are they substitutes for proper accident prevention measures.
Original Language Version
TJ1000F, TJ1500F ISSUE No:1 - 05/01/10
