background image

 

 
2. PERSONAL PRECAUTIONS 

 
RISK  OF  EXPLOSIVE  GASES.  A  SPARK  NEAR  THE  BATTERY 
MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE RISK 
OF A SPARK NEAR THE BATTERY: 
 

2.1. NEVER smoke or allow a spark or flame in the vicinity of a battery or engine. 
2.2. Do not permit the internal battery of the Roadstart® to freeze. Never charge a frozen battery. 
2.3.  When  charging  the  internal  battery,  work  in  a  well  ventilated  area  and  do  not  restrict  the  
         ventilation in any way. 
2.4. Be sure the area around the battery is well ventilated while the Roadstart® is being used. 
2.5. Remove personal metal items such as rings, bracelets, necklaces and watches when working with  

a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a 
ring or the like to metal, causing a severe burn. 

2.6. Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might spark or  
       short-circuit the battery or other electrical part that may cause an explosion. 
2.7. To prevent sparking, NEVER allow clamps to touch together or contact the same piece of metal. 
2.8. Consider having someone close enough by to come to your aid when you work near a lead-acid  
        battery. 
2.9. Have plenty of fresh water and soap nearby in case battery acid contacts your skin, clothing or  
        eyes. 
2.6. Wear complete eye and body protection, including safety goggles and protective clothing. Avoid  
        touching your eyes while working near the battery. 
2.7. If battery acid contacts your skin or clothing, immediately wash the area with soap and water. If  
        acid enters your eye, immediately flood the eye with cold running water for at least 10 minutes  
        and get medical attention right away. 
2.8. If battery acid is accidentally swallowed, drink milk, the whites of eggs or water. DO NOT induce  
        vomiting. Seek medical attention immediately. 
2.9. This appliance can be used by children aged from 8 years and above and persons with reduced  

 physical, sensory or mental capabilities or lack of experience and knowledge if they have been  
 given supervision or instruction concerning use of the appliance in a safe way and understand 
 the hazards involved 

2.10. Children shall not play with the appliance. 
 
3. PREPARING TO USE THE ROADSTART® 

 

RISK OF CONTACT WITH BATTERY ACID. BATTERY ACID IS 
A HIGHLY CORROSIVE SULFURIC ACID. 

 
 

 

3.1.  Clean the battery terminals before using the  Roadstart®. During cleaning, keep airborne corrosion  
          from coming into contact with your eyes, nose and mouth. Use baking soda and water to neutralize  
 

the battery acid and help eliminate airborne corrosion. Do not touch your eyes, nose or mouth. 

3.2.  Read,  understand  and  follow  all  instructions  for  the  Roadstart®,  battery,  vehicle  and  any 
equipment   
        used near the battery and the Roadstart®. 
3.3. Determine the voltage of the battery by referring to the vehicle owner’s manual and make sure  
        that the output voltage of the Roadstart® is correct. 

Summary of Contents for ROADSTART PBI2212GS
















Reviews: