2. INTRODUCTION & SPECIFICATIONS
The SA2110/3, SA2115/3 and SA2120/3 Premier Line Compressors have twin cylinder pumps belt driven by 230V 1ph motors and are capable
of supplying air at up to 10 bar from 100 to 200 litre tanks. In addition to pneumatic tools, the compressors may be connected to accessories suitable
for blowing, washing, spraying and tyre inflation. SA2110/3 has two rear wheels, a castor front wheel and a handle for ease of movement.
SA2110/3, SA2115/3 & SA2120/3 - 1069 - (2) - 150200
3. PREPARATION
3.1.
Remove compressor from packaging and inspect for any shortages or damage. If anything is found to be missing or damaged contact your supplier.
3.2.
Save the packing material for future transportation of the compressor. We recommend that you store the packing in a safe location, at
least for the period of the guarantee. Then, if necessary, it will be easier to send the compressor to the service centre.
3.3.
Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.
3.4.
The compressor should be operated on a flat surface, or one that does not exceed 15
O
either transversely or longitudinally (fig.1), and
should be in a position that allows good air circulation around the unit.
3.5.
Fit the air filter (fig.2) to the inlet port of the cylinder head. SA2110/3 - Screw the stud provided into the tapped hole at the rear of the
port and mount circular filter A with wing nut. SA2115/3 and SA2120/3 - Attach filter B with the two bolts and gasket provided.
3.6.
Confirm that the oil level is at the maximum mark on the sight glass (fig.3).
fig. 1
Free Air Delivery
(cfm)
Model
Max
Motor
Output
(hp)
Voltage/
Phase
Current
(A)
Pump
Type
Pump
Speed
(rpm)
Piston
Displacement
(cfm)
At
2.5 Bar*
Max.
At
6.0 Bar*
Tank
Capacity
(l)
Max.
Pressure
(psi/bar)
Noise
Level
(dB.A)
SA2110/3
3
230/1
13
K17
1180
14.9
11.6
12.0
10.6
100
145/10
73
SA2115/3
3
230/1
13
K17
1180
14.9
11.6
12.0
10.6
150
145/10
74
SA2120/3
3
230/1
13
K17
1180
14.9
12.0
11.6
10.6
200
145/10
74
2.1.
Specifications
2.2.
Weights & Dimensions
Model
Weight
(kg)
Dimensions
Length x Width x Height (mm)
SA2110/3
78
1140 x 420 x 890
SA2115/3
82
1280 x 410 x 880
SA2120/3
94
1410 x 470 x 920
fig. 3
fig. 2
s
DANGER! DO NOT direct the output jet of air towards people or animals.
DO NOT operate the compressor without an inlet air filter (see figure 2).
DO NOT allow anyone to operate the compressor unless they have received full instructions.
p
WARNING!
The air tank is a pressure
vessel and the following safety measures apply:
DO NOT tamper with the safety valve and DO NOT modify or alter the tank in any way and DO NOT strap anything to the tank.
DO NOT subject the tank to impact, vibration or to heat and DO NOT allow contact with abrasives or corrosives.
DO drain condensation from tank daily, inspect inside walls for corrosion every three months and have a detailed tank inspection
carried out annually.
The tank shell must not fall below the certified thickness at any point.
p
WARNING!
If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating (See part 1.1.11).
When not in use, store the compressor carefully in a safe, dry, childproof location.
A
B
All performance figures are ± 5%
