3.1. Air Supply
3.1.1. Ensure the polisher air control valve (or throttle) is in the "Off" position before connecting to the air supply.
3.1.2. You will require an air pressure of 90psi, and an air flow according to the specification above.
3.1.3.
p
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the polisher.
Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may
be dangerous, causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the polisher
and will invalidate your warranty.
3.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig.2.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.7. Keep hose away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings
3.2.1 Vibration may cause failure if a quick change coupling is connected directly to the air polisher.
To overcome this, connect a leader hose to the polisher. A quick change coupling may then be used to
connect the leader hose to the air line recoil hose. See figs.2 & 3.
p
WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before use.
4.1. Assembly
4.1.1. Screw the backing pad into the polisher spindle, then tighten with supplied spanner. Apply the polishing
disc, use only discs with speed ratings equal to or higher than the speed rating of the polisher.
DO NOT
use cloth backed polishing discs.
4.1.2. Connect air supply to polisher, slide the safety catch (fig.1.1) and press the control valve lever (fig.1.2) to
check that the polisher is working correctly.
4.1.3. The air flow may be regulated by adjusting the regulator valve in the back of the handle.
4.2. Operating
4.2.1. The polisher is designed to provide a combined “rotary” and “random orbit” action.
4.2.2.
Always use a polish appropriate for the job.
Composite handle with rear exhaust reduces effects of
chill and noise level. Air motor with quality bearings for
smooth and powerful operation. Fitted with safety
trigger to prevent inadvertent operation. Integral gear
system reduces output speed, while maintaining a high
torque level. Supplied with hook-and-loop pad for use
with buffing and polishing heads - for full range see
pages 650 & 651 of your Sealey catalogue. Ø50mm
Hook-and-loop pad available separately (order Model
No. PTC50VA).
Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø75mm
Motor Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5hp
Free Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 2600rpm
Operating Pressure . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption . . . . . . . . . . . . . . . . . . . . . . . . . 4cfm
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Noise Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 94dB.A
Noise Pressure. . . . . . . . . . . . . . . . . . . . . . . . . 83dB.A
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.41m/s²
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.08kg
3. PREPARING TOOL FOR USE
4. OPERATING INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
Original Language Version
SA704 Issue: 1 - 12/10/11
fig.2
fig.3
