Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
7. TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
REMEDY
1A) Pressure drop in the tank
Air leaks at connections
Run compressor to max. pressure, switch off.
Brush soap solution over connections and look for
bubbles. Tighten connections showing leaks.
If problem persists contact Authorised Service Agent
1B) Pressure drop in the tank
Air leaks from safety valve
It should be replaced, unless leaking at a joint
which can be sealed.
1C) Pressure drop in the tank
Air leaks from cylinder head gasket
Check tightness of head bolts. If leak continues
contact authorised Service Agent
2) Pressure switch valve leaks when
compressor is idle
non-return valve seal defective
Empty the air tank. Referring to fig.8 remove the
non-return valve cap (3), spring (2) and seal (1).
Clean the seal and its seat, or if necessary replace
the seal
3) Air leaks from tank body or tank welds
Internal corrosion caused by infrequent tank
draining or non permitted modifications to tank
Cannot be repaired
DISCONTINUE USE IMMEDIATELY
4A) Motor stops and will not restart
Thermal cut out has operated
Allow unit to cool for 30 minutes before restarting
4B) Motor stops or stalls and will not restart
Supply breaker has tripped
A qualified electrician to check breaker and restart.
If repeated tripping occurs replace the check valve
or contact authorised Service Agent
5) Compressor stops and does not restart
Motor failure
Contact Authorised Service Agent
6A) Compressor does not stop at max. pressure
Pressure switch fault
Contact Authorised Service Agent
6B) Compressor does not stop at max. pressure
Filter clogged
Head gasket or valve fault
Replace filter element.
Contact Authorised Service Agent
7) Compressor noisy with metallic knock
Bearing or piston damage
Contact Authorised Service Agent
8) Excessive moisture in discharged air
High humidity environment
drain tank after each use
fig.8
6.8.
IMPORTANT WARNING - Air contaminants taken into the compressor will affect optimum performance. For example, body
filler dust or paint overspray will clog the pump intake filter and may cause internal damage to the pump or motor. Please note
that any parts damaged by any type of contamination will not be covered by the warranty
6.9.
Inspection of pressure tank both internal and external is essential. under the
PRESSURE SYSTEMS SAFETY REGULATIONS 2000
it is the responsibility of the owner of the compressor to initiate a system of inspection that both defines the frequency of the inspection
and appoints a person who has specific responsibility for carrying out the inspection.
6.10. DO NOT
carry out any welding operations on any pressurised parts of the vessel.
SAC42055B.V2, SAC52775B.V2, SAC62710B.V2 Issue: 1 - 16/12/16
Original Language Version
© Jack Sealey limited
