SB951, SB972 - 0016 - (1) - 070200
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
INSTRUCTIONS FOR:
SHOT BLASTING CABINETS
Models:
SB951 & SB972
1.1.
ELECTRICAL SAFETY.
p
WARNING! It is the users responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and all
electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are
plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on a business premises, to be tested by
a qualified Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require
a fuse smaller than 13Amps for certain products (
subject to 1.1.10. below)
see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. Products such as
welders must not be pulled or carried by their output cables.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by
a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut off
and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal E.
b) Connect the BROWN live wire to live terminal L.
c) Connect the BLUE neutral wire to the neutral terminal N.
After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked with
this symbol .
To re-wire, connect the brown & blue wires as indicated above. DO NOT
connect the brown or blue to the earth terminal.
1.1.10. Some products require more than a 13Amp electrical supply. In such a case,
NO
plug will be fitted.
You must
contact a qualified Electrician
to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug & socket with your electrician.
1.1.11.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important. We recommend that at least 1.5mm
2
section cable but to be absolutely sure that the capacity of the cable reel is
suitable for this product and for others that may be used in the other output sockets, we recommend the use of 2.5mm
2
section cable.
Blue
Neutra
l
Yellow & Green
Earth wire
wire
restrai
FUSE RATING
THIS PRODUCT MUST BE FITTED
WITH A:
13
Amp FUSE
Brown
Live
wire
1.2 GENERAL SAFETY
p
WARNING!
Ensure health & safety, government and local authority regulations relating to the the use of shot blasting are adhered to when
using this equipment. Familiarise yourself with cabinet application and limitations, and specific potential hazards peculiar to the
cabinet
.
p
WARNING!
Disconnect the cabinet from the mains power, and air supply before attempting to changing accessories, servicing or
performing any maintenance.
3
Maintain the
cabinet
in good condition Replace or repair damaged parts.
Use genuine parts only. Non authorised parts may be dangerous
and will invalidate the warranty.
3
Locate cabinet in an adequate working area for its function, keep area clean, tidy and free from unrelated materials. Ensure adequate lighting.
3
Use only dry abrasives such as glass bead. We recommend Sealey item B5KG. Never use harsh abrasives such
as aluminium oxide, blasting garnet or sand with this cabinet. Never use fluids or mix fluids with another media in the unit.
p
WARNING!
Always wear approved eye or face and ear protection when operating the
cabinet
.
3
Keep the unit lid closed and secured when in use.
p
WARNING!
ensure correct air pressure is maintained and not exceeded.
Always keep the blast nozzle directed at the workpiece. Never use outside the unit, always use with the lid closed.
Regularly check the exhaust vent at the back of the cabinet is clear and not blocked and there is space between it and any wall.
3
Maintain correct balance and footing. Ensure the floor is clean and free from blasting grit spillage. Wear non slip shoes.
3
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
3
Keep children and non essential persons away from the working area.
3
Use a dust free light tube not greater than 70 Watts.
7
DO NOT force the
cabinet
to achieve a task it was not designed to perform.
7
DO NOT operate the
cabinet
if any parts are damaged or missing as this may cause failure or possible personal injury.
7
DO NOT operate the cabinet with the lid open.
7
DO NOT stand on the cabinet.
