Gun Cabinet
model no:
SKGS3, SKGS5, SKGS8
thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. Safety
WaRninG!
These gun cabinets are heavy and care should be exercised in transit and handling to ensure that no one is injured.
WaRninG!
The gun cabinets are a 2 person job for transit and installation.
9
For maximum security, these gun cabinets must be securely fixed to a wall or floor.
9
Ensure that if secured to the wall, the cabinet is on a firm level surface.
8
DO nOt
install in areas where damp and condensation are present.
WaRninG!
The warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
2. intRODuCtiOn
Heavy-duty gun cabinets with powder coated paint finish to prevent corrosion. Each cabinet door is evenly locked by five 25mm locking bolts,
one top, one bottom and three along the side. Each cabinet includes a set of securing bolts with rear and bottom holes for fixing to the wall and
floor. Side walls and floor are carpeted to protect guns from damage when putting away or taking out of the cabinet. SKGS Series include two
large keys for locking the main door and two small keys for locking the internal ammo safe. Each gun cabinet is manufactured in accordance
with BS 7558:1992.
3. SpeCifiCatiOn
model no: ..................................................................
SKGS3
external dimensions (W x d x H): .........
250 x 250 x 1450mm
G
un Capacity: ............................................
3 (Max. 1260mm)
Internal dimensions (W x d x H): ..........
245 x 175 x 1260mm
nett Weight: ..............................................................
36.62Kg
model no: ..................................................................
SKGS5
external dimensions (W x d x H): .........
350 x 340 x 1450mm
G
un Capacity: ............................................
5 (Max. 1260mm)
Internal dimensions (W x d x H): ..........
345 x 270 x 1260mm
nett Weight: ..............................................................
50.93Kg
model no: ..................................................................
SKGS8
external dimensions (W x d x H): .........
490 x 360 x 1450mm
G
un Capacity: ............................................
8 (Max. 1260mm)
Internal dimensions (W x d x H): ..........
485 x 290 x 1260mm
nett Weight: ..............................................................
64.24Kg
4. inStallatiOn
4.1.
Consideration should be given to the placing of the gun cabinet to ensure
that it is placed in a discreet location and will not be easily found by
intruders.
4.2.
Each gun cabinet is supplied with
a set of anchor bolts suitable for fixing to
brick and concrete.
4.3.
Fixing to hollow partition walls is not recommended. If fixed to wood it must
be to a solid wooden structure.
4.4.
open the door of the gun cabinet
(see 5.1 for opening instructions)
and
with the help of a second person, position it where required and mark the
mounting positions through the pre-drilled holes in the back or base of the
gun cabinet.
4.5.
Drill 12mm holes to a depth of 67mm (fig.1.1) and insert the anchor
sleeve
and
nut
with bolt and washer removed (fig.1.2).
4.6.
Position the gun cabinet over the anchor holes. Place a washer over the
anchor bolt and insert into sleeve through the gun cabinet, screw into nut
and tighten to secure. (fig.1.3).
S
KGS3 SKGS5 SKGS8 Issue 3 (HF) 08/05/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
fig.1
SKGS3
SKGS8
SKGS5
