1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
INSTRUCTIONS FOR:
BELT/DISC SANDER 25 x 762mm 250W/230V
MODEL No:
SM750
1.1.
ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 198
9 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and
dispose of the plug safely
.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b)
Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the
restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above -
DO NOT
connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and
socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm2, but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm2 section cable.
RECOMMENDED
FUSE RATING: 5 AMP
© Jack Sealey Limited
Original Language Version
SM750 Issue No.1 27/11/12
1.2.
GENERAL SAFETY
WARNING!
Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
WARNING!
Disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
WARNING! DO NOT
sand any materials containing asbestos.
Ensure the operating voltage stated on the ratings plate corresponds to your mains power supply.
Check the belt and disc sander and the electrical connections for any damage and
DO NOT
use the tool if the sander or the cable is
damaged.
Ensure that the belt and disc sander is switched off before plugging in to the mains power supply.
Persons with limited physical, sensory or mental abilities are not allowed to use the unit, unless they are fully supervised and briefed on
safety issues by a qualified person.
Use the belt and disc sander according to this manual and only for the purpose for which it is designed.
Before starting up, make sure that no spanners or adjusting keys are attached to the machine.
Avoid contact with grounded surfaces such as radiators, pipes etc.
Maintain correct balance and footing, ensure that the floor is not slippery and wear non-slip rubber soled footwear.
NOTE:
Remember that the disc and belt will still be moving for several seconds whilst slowing down,
after
switching off.
Familiar yourself with your working area and be alert for possible hazards, which you might not hear due to machine noise.
Inspect the work piece and remove all nails and screws before sanding.
Be aware that sparks may ignite the dust or fumes.
Switch off the belt and disc sander before making any adjustments and when the unit is not in use.
After finishing work and maintenance, disconnect the power lead from the mains supply.
In the event of an electrical or mechanical malfunction, immediately switch off the sander and do not use it further.
Always keep your work area clean.
Never use the power cable to carry the belt and disc sander. Keep the cable away from hot, sharp edges and moving parts.
WARNING!
Always wear gloves and safety goggles and a dust mask as some coatings and wood dust may be harmful and toxic.
