2. INTRODUCTION & SPECIFICATIONS
Portable electric multipurpose sharpener, aimed at the DIY user. Sharpens all HSS drill bits from 3mm to 10mm, straight edged knives and
scissors. Also regrinds chisels and plane blades up to 50mm wide.
© Jack Sealey Ltd
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SMS2004
Input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V, 50Hz
Free Speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6700rpm
Wheel Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø48mm
Minimum Drill Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . Ø3mm
Maximum Drill Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . Ø10mm
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.65kg
3. INSTALLATION
4. OPERATION
3.1. INSTALLATION
3.1.1. Screw the sharpener securely to a fireproof workbench, using the screwholes in the base as a template.
4.1.
HIGH SPEED DRILL SHARPENER (Refer to fig.1).
4.1.1. Slide module labelled 'High Speed Drill Sharpener' (1) onto the power unit.
4.1.2. Remove the clamp from the clamp holder and insert the drill bit (2) to be sharpened (1a). Tighten the clamp lightly to leave the drill bit
still free to move.
4.1.3. Place the clamp containing the drill bit into the setting slot on the left hand top (see 3 in fig.1), using the grooves in the side to lower it in
correctly (1b).
4.1.4. Move the drill bit cutting end forward, so that it lays in the V guide and touches the metal end stop (1c).
4.1.5. Turn the drill bit until the V guide fully drops over it (1c), all four drill corners should now be touching the V guide sides.
4.1.6. Ensure that the drill and holder are fully down in the setting slot. With the drill in this position, tighten the clamping ring (1d).
4.1.7. Lift up the V guide and remove the clamp holder and drill bit.
4.1.8. Transfer the clamp holder to the sharpening position, on the right hand top(1e), secure it with light finger pressure (1f).
4.1.9. Switch the power unit on.
Fig.1
4.1.10. Move the clamp holder from side to side, securing with light finger pressure.
4.1.11. Remove the drill bit and holder and turn it over to sharpen the other face of the drill (1g).
4.1.12. Check that the leading edge of both flutes are equally sharp (1h).
4.1.13. Switch the power unit off. Before removing the module, ensure the grinding wheel has stopped.
DO NOT
touch the sharpening disc whilst operating, or whilst plugged into the mains power.
DO NOT
leave the sharpener running unattended.
DO NOT
operate the sharpener when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
attach modules if the wheel is still moving and
DO NOT
use without a module in place.
The motor is specially rated for intermittant use, use a maximum of 15 minutes continuous use.
When not in use switch sharpener off, remove plug from power supply.
DO NOT
try to cool the sharpening wheel with water or other lubricants.
1. SAFETY
Original Language Version
SMS2004 Issue:4 (H,F) - 22/01/18
