background image

Sealey Group,

Bury St. Edmunds,

Suffolk. 

01284 757500

01284 703534

E-mail:

sales@sealey.co.uk

Declaration of Conformity 

We, the sole importer into the UK, declare that the product

s

listed below 

are

in conformity with the following

EEC standards and directives.

The construction file

s

for th

ese

product

s are

held by the Manufacturer 

and may be inspected by a national authority upon request to Jack

Sealey Ltd

For Jack Sealey Ltd. Sole importer into the UK of Sealey  

as Power Welders

Signed by Mark Sweetman

Models: 

SUPERMIG185, SUPERMIG195/9.

Low Voltage Directive (S.I. 1994/3260) 73/23/EEC

EMC Directive (S.I. 1992/2372 & Amendments).

89/336/EEC

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter

data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this equipment

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for

any claim.

INFORMATION: 

Call us for a copy of our latest catalogue on 01284 757525 and leave your full

name and address including your postcode.

Supermig185, 195/9,  0051 (2) 180900

Summary of Contents for SuperMig185









Reviews: