background image

instructions for

MANUAL TYRE CHANGER

model no: 

TC960.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

‰

   WARNING!

 ensure Health & safety, local authority and general workshop practice regulations are adhered to when using this  

 

 equipment.

 

9

   familiarise yourself with the applications, limitations and the potential hazards of the tyre changer.

 

9

   maintain  the

 

tyre changer in good condition (use an authorised service agent).

 

9

   replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

‰

  

WARNING!

 check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next  

  used.  

 

9

   locate the tyre changer in a suitable work area and keep area clean and tidy and free from unrelated materials. ensure that there is adequate  

 lighting.

 

‰

   WARNING! 

use on a level surface, preferably concrete, 

to which the tyre changer must be bolted. 

 

9

   Keep the tyre changer clean for best and safest performance.

 

9

   Wear approved safety eye protection (standard spectacles are not adequate).

 

9

   Keep hands and feet well clear of the bead breaker.

 

9

   maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.

 

9

   remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

 

9

   Keep children and unauthorised persons away from the work area.

 

8

   DO NOT

 use the tyre changer for any purpose other than that for which it is designed.

 

8

   DO NOT

 operate the tyre changer if any parts are damaged or missing as this may cause failure and/or personal injury.

 

8

   DO NOT

 allow untrained persons to operate the tyre changer.

 

8

   DO NOT

 stand on the tyre changer.

 

8

   DO  NOT

 operate the tyre changer when you are tired or under the influence of alcohol, drugs or intoxicating medication.

2.  INTRODUCTION

steel construction with manual bead breaker. suitable for use on most open centred wheels. supplied with tyre bar. to prevent damage to the 

rims of an alloy wheel, it is essential to use a tc963 tyre Bar.

3.  SpECIFICATION

Model no: ..............................................................TC960.V2

min. Wheel diameter ............................................................n/a

max. Wheel diameter ...........................................................n/a

min. Wheel depth ..............................................................0mm

max. Wheel depth .........................................................300mm

Working Height ..............................................................640mm

centre Post sizes ............................................................41mm

4.  ASSEMbLY

 

Numbers/letters in brackets refer to those shown in the parts diagram.

4.1.    

Attach the pedestal (3) to the base (1) using the bolts (11), washers (14) and nuts (12) provided. note that the longer end of the base 

 

 

should be below the bead breaker (7). 

4.2.    

Attach the two side base channels (2) to the pedestal using bolts, washers and nuts, as above.

 

Note: 

there are two holes in the base and one in each side base for securely mounting the tyre changer to the floor.

5.  OpERATION

5.1.  the 

TC960

 tyre changer is manually operated - no air supply is required. it is designed for removing/fitting tyres from/to most  

 

sizes of open-centre wheels (see section 3 specification). 

DO NOT 

use the tyre changer for any other purpose.

5.2.    

if tyres are to be changed on aluminium wheels the optional tyre bar, sealey model no. 

TC963

, must be used to prevent damage to the    

 wheel rims.

 

  

IMpORTANT! 

never attempt to fit or remove a tyre without first lubricating both beads (lubricant not supplied).

5.3.    

bead breaking - refer to fig. 1

5.3.1.   

deflate the tyre and remove all balance weights.

refer to

instruction

manual

Wear eye

protection

Wear

safety

footwear

Wear

protective 

gloves

tc960.V2 | issue 1 23/11/17

Original Language Version

© Jack sealey limited

Reviews: