Wheel Skate
Model no:
WS680.V2
thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. Safety
WaRNING!
ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9
Familiarise yourself with this product’s application and limitations, as well as the specific warnings below relating to their use.
9
ensure the Wheel Skates are in sound condition and good working order. Take action for immediate repair or replacement of damaged
parts.
Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
9
Wheel Skates should only be used in suitable, well lit areas.
9
Wheel Skates must be used in pairs at either the front or rear of the vehicle. they must never be used diagonally.
9
Keep general area clean and tidy and free from obstructions.
9
Use Wheel Skates on level and solid ground, preferably concrete. Avoid tarmacadam as Wheel Skates may sink in.
9
Maintain the Wheel Skates in good condition (use an authorised service agent).
9
ensure there are no passengers in the vehicle.
9
ensure the Wheel Skates are free to move and that there are no obstructions in the area of use.
9
When not in use store Wheel Skates in a safe, dry, childproof area.
▲
DaNGeR:
Use the Wheel Skates for manoeuvring or positioning of vehicles in interior situations. They are not designed for use
outdoors.
8
DO NOt
start or drive the vehicle whilst it is raised on wheel skates.
8
DO NOt
use the Wheel Skates for purposes other than that for which they are intended.
8
DO NOt
allow untrained persons to operate the Wheel Skates.
8
DO NOt
leave the vehicle unattended whilst it is raised on the Wheel Skates.
8
DO NOt
operate the Wheel Skates when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOt
get the Wheel Skates wet or use in damp or wet locations or areas where there is condensation.
8
DO NOt
exceed the rated capacity of the Wheel Skates. Remember that the front of a vehicle is usually heavier than the rear.
8
DO NOt
use the Wheel Skates to lift or support a vehicle in order to do work underneath it.
9
Maintain correct balance and footing when moving vehicle. ensure the floor is not slippery and wear non-slip shoes.
9
ensure there are no obstructions beneath the vehicle when it is to be lowered.
9
ensure all non-essential persons keep a safe distance whilst the Wheel Skates are in use.
IMPORtaNt -
We recommend that at least 2 persons are involved in manoeuvring the vehicle when supported on wheel skates. The
vehicle’s weight provides a large amount of inertia which has to be overcome to get the vehicle moving and more importantly, stopped.
WaRNING!
The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. INtRODuctION
Steel tube chassis with four Ø100mm nylon castors. Pedal operated hydraulic lifting action with safety locking pin when under load. Composite
rollers cradle vehicle’s tyre and are capable of handling up to 240mm profile. Suitable for body shops, garages, showrooms or anywhere a
disabled vehicle needs moving on an even surface.
3. SPecIfIcatION
lifting capacity per Skate: ...............................................680kg
Maximum opening: .......................................................540mm
Maximum Tyre Profile: ...................................................240mm
Wheel Ø: ....................................................................Ø100mm
Weight (each): ...................................................................17kg
4. PRePaRatION
4.1.
Ensure that the area where the vehicle is to be moved is clear of any obstructions. The floor surface should be smooth and level.
4.2.
Take note of any features in the floor that may catch the skate wheels such as floor mounted power and data points, room divider
tracks, drainage features, or damage to the floor surface.
4.3.
Enlist a sufficient amount of people to move the vehicle safely.
8
DO NOt
attempt to move the vehicle into an area where there is insufficient space to manoeuvre the vehicle safely.
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear safety
footwear
WS680.V2 Issue 1 06/11/18
