Sea Dragon 4500
Pro Photo/ Video Light
(Item SL675)
4500
QUICK Guide
Carry
Case
1” ball joint
adapter with
w/ hex key
SEALIFE (C/O PIONEER RESEARCH),
97 FOSTER ROAD, MOORESTOWN, NJ 08057 USA
INFO@SEALIFE-CAMERAS.COM WWW.SEALIFE-CAMERAS.COM
START
Charge the battery.
Status light on AC
power adapter turns
from red to green when
battery is fully charged.
Note: Battery is pre-
installed in the light.
Remove yellow contact
cover, which prevents
accidental power on
during transportation.
What’s in the box:
Sea Dragon
4500 light head
with YS adapter
attached
1
1
Sea Dragon
Overview:
The Sea Dragon Pro Photo/Video light delivers 4500 true lumens in a smooth, even 120°
wide beam without hotspots. Unmatched 96 CRI (color rendering index) and 97 TLCI (Television
Lighting Consistency Index) COB LED array that mimics natural sunlight. Brightness is adjusted
manually in 4 steps (100% 75%, 50% and 25%) or automatically (from 10% to 100%) with its built-in
photocell light sensor. The flash-detect feature turns off the light for 1 sec. when nearby flash is fired.
The light easily mounts to YS, 1” ball joint or Flex-Connect system of arms, grips, trays and mounts.
The 50Wh battery delivers 1hr run time at full power and 4hrs at 25% brightness.
Flex-Connect
YS adapter
2
2
Check if O-rings are lubed.
O-ring should appear shiny. If
not, apply small amount of silicon
lube to outside surface of O-rings.
Wipe off excess lube.
50W Li-ion battery
with protective cover,
charging tray and AC
power adapter
Int’l plug adapters
for EU, UK and AU
Spare O-rings w/ lube
and emoval tool
3
3
Insert battery in light and
screw on waterproof battery
cap until fully seated.
4
4
Connect light head to arm or grip (Sold seperately).
Use Flex-Connect YS adapter if connecting light to
Flex-Connect system of arms, grips and trays. Light
may also be mounted directly to YS arms and grips.
Replace YS adapter with included ball joint adapter
if mounting to ball joint arms and grips.
Push and hold power
button for 1 second to
power light on and off.
5
5
Push and release the power button to
cycle through 5 different brightness
modes: 100%
¤
75%
¤
50%
¤
25%
¤
Auto
¤
[repeat].
6
6
Battery status indicator will be green when battery is 30% to 100% charged,
yellow when battery is 15% to 29% charged and red when battery is near
empty. There is a 10-minute 70-lumen safety reserve before light powers
off when battery is empty and - status indicator will blink red.
7
7
To activate emergency signal mode, push and hold
power button for 4 seconds from power off state.
Push and release power button to select between 1
sec blink interval and SOS Morse code.
The Auto Flash Detect (AFD) feature is already activated. The
light will power off for 1 sec. when nearby flash is fired. To
deactivate AFD, push and hold power button for 5 seconds
from power off state. Push and release power button to select
between AFD off (1 blink per sec.) and AFD on (2 blinks).
9
9
8
8
IMPORTANT:
1.
Avoid using the light above water for more than a few minutes. The front of the light head becomes very hot within a few minutes,
which may cause burning if touched. Water is needed to keep the light cool. A thermal sensor will dim the light if it overheats.
2.
After use, soak sealed light in fresh water for 20 minutes to dissolve salt residue. Towel dry. Allow light to fully dry before
storage.
3.
If water has entered the battery compartment or under the lens port, immediately power off the light. On land, remove
the battery. Allow battery compartment to fully dry. Contact your local SeaLife dealer or SeaLife service center in your
country for repair service.
4.
Do not use battery that has become wet or if outer casing is cracked or damaged. Dispose of wet or damaged battery in
accordance with your local battery recycling regulations.
5.
Remove battery from light before transporting, traveling or long term storage. Always use the included protective battery cover
when battery is not inside the light or charging tray to prevent accidental short-circuiting the battery contacts.
6.
Do not obstruct the safety pressure release valve located under the light head.
7.
Observe all SCUBA dive safety rules and control your buoyancy at all times. Consult your dive instructor for dive safety questions.
8.
Visit SeaLife-Cameras.com for troubleshooting advice, updates to these instructions, spare parts and other helpful information.
GUARANTEE:
SeaLife warrants the original
purchaser of this product, for a period of
one (1) year from the date of purchase,
that the product is free from defects in
workmanship and materials. In the event the
original purchaser believes there is a defect
in a product, it is recommended that the
purchaser first visit www.sealife-cameras.
com for product updates and information on
how to get warranty repair service. Please
contact your local SeaLife dealer or the
importer in the country where the product
was purchased for return information.
APRIL 2018
