background image

FT500 INSTRUCTIONS

Seametrics • 253.872.0284 

Page 11 seametrics.com

The limited warranty set forth below is given by Seametrics, with respect to Seametrics and INW brand products purchased in the 

United States of America.
Seametrics warrants that products manufactured by Seametrics, when delivered to you in new condition in their original containers 

and properly installed, shall be free from defects in material and workmanship. 

Seametrics products are warranted against 

defects for a period of two (2) years from date of installation, with proof of install date. If no proof of install date can be 

provided, warranty period will be two (2) years from date of shipment from Seametrics, as defined on Seametrics’ invoice. 

Seametrics’ obligation under this warranty shall be limited to replacing or repairing the part or parts, or, at Seametrics’ option, the 

products, which prove defective in material or workmanship. The following are the terms of Seametrics’ limited warranty:

a.  Buyer must give Seametrics prompt notice of any defect or failure and satisfactory proof thereof.
b.  Any defective part or parts must be returned to Seametrics’ factory or to an authorized service center for inspection. 
c.  Buyer will prepay all freight charges to return any products to Seametrics’ factory, or another repair facility. as designated by 

Seametrics.

d.  Defective products, or parts thereof, which are returned to Seametrics and proved to be defective upon inspection, will be 

repaired to factory specifications.

e.  Seametrics will deliver repaired products or replacements for defective products to the buyer (ground freight prepaid) to the 

destination provided in the original order. 

f.  Products returned to Seametrics for which Seametrics provides replacement under this warranty shall become the property 

of Seametrics.

g.  This limited warranty covers all defects encountered in normal use of Seametrics products, and does not apply to the 

following cases:
i. 

Loss of or damage to Seametrics product due to abuse, mishandling, or improper packaging by buyer

ii. 

Failure to follow operating, maintenance, or environmental instructions prescribed in Seametrics’ instruction manual

iii. 

Products not used for their intended purpose

iv. 

Alterations to the product, purposeful or accidental

v. 

Electrical current fluctuations

vi. 

Corrosion due to aggressive materials not approved for your specific product

vii. 

Mishandling, or misapplication of Seametrics products

viii. 

Products or parts that are typically consumed during normal operation

ix. 

Use of parts or supplies (other than those sold by Seametrics) which cause damage to the products, or cause 

abnormally frequent service calls or service problems

h.  A new warranty period shall not be established for repaired or replaced material, products, or supplied. Such items shall 

remain under warranty only for the remainder of the warranty period on the original materials, products, or supplies.

i.  In the event that equipment is altered or repaired by the buyer without prior written approval by Seametrics, all warranties 

are void. Damage caused by equipment or accessories not manufactured by Seametrics may void the product’s warranty.

j.  SOFTWARE: The Seller grants the user a non-exclusive license to use Seametrics’ software, according to the following 

limitations and conditions:
i. 

The user may install the software on one or more desktop or laptop computers.

ii. 

All title and intellectual rights to the software are owned by Seametrics. 

iii. 

No copies may be made or distributed except as described above. 

iv. 

The user may not modify or reverse-engineer the software.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER ORAL, WRITTEN, EXPRESSED, IMPLIED OR STATUTORY. 

NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, 

APPLIED TO THE PRODUCTS AFTER THE APPLICABLE PERIOD OF THE EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER 

EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE 

PRODUCTS, SHALL BIND SEAMETRICS. SEAMETRICS SHALL NOT BE LIABLE FOR LOSS OF REVENUES, OR PROFITS, OR INCONVENIENCES, 

EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OF DATA, OR ANY OTHER SPECIAL, INCIDENTAL, OR 

CONSEQUENTIAL DAMAGE CAUSED BY THE USE OR MISUSE OF, OR INABILITY TO USE THE PRODUCTS, REGARDLESS OF THE LEGAL 

THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SEAMETRICS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO 

EVENT SHALL RECOVERY OF ANY KIND AGAINST SEAMETRICS BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT 

SOLD BY SEAMETRICS AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK OF LIABILITY 

FOR LOSS, DAMAGE, OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE OR MISUSE 

OF, OR INABILITY TO USE THE PRODUCTS NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SEAMETRICS.
SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATIONS MAY NOT 

APPLY TO YOU. SIMILARLY, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF CONSEQUENTIAL DAMAGE, SO THE 

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS; HOWEVER, 

YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.  

SEAMETRICS LIMITED WARRANTY

Summary of Contents for FT500 Series













Reviews: