background image

20

Attaching the Lat Bar or Nylon Strap to the
High Pulley Station

Attach the Lat Bar (54) to the Short Cable (23) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the Medium
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Medium Cable so
the Lat Bar is in the correct starting position for the
exercise to be performed.

The Nylon Strap (39) can be attached in the same man-
ner.

54

53

52

23

39

Adjustment

Changing the Weight Setting

To change the weight setting of the weight stack, insert a
Weight Pin (26) under the desired Weight (25). Be sure to
insert the Weight Pin until the bent end of the Weight Pin
is touching the Weights, and turn the bent end downward.
The weight setting of the weight stack can be changed
from 6.5 pounds to 106.5 pounds, in increments of 12.5
pounds. Note: Due to the cables and pulleys, the
amount of resistance at each exercise station may
vary from the weight setting. Use the WEIGHT
RESISTANCE CHART on page 23 to find the approxi-
mate amount of resistance at each weight station.

25

26

Attaching and Removing the Butterfly Seat

Set the bracket on the Butterfly Seat Frame (36) onto the
indicated pins on the Butterfly Upright (42). Attach the
Butterfly Seat Frame to the Butterfly Upright with the
5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).

For some exercises, the Butterfly Seat Frame (36) must
be removed. First, be sure that the chain is not attached
to the leg lever. Next, remove the Seat Knob (40) and the
5/16” x 2 3/4” Carriage Bolt (14) from the Seat Frame. Lift
the Seat Frame off the Butterfly Upright (42).

40

A

42

14

36

The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise
poster accompanying this manual to see how the home gym system should be set up for each exercise.
IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor-
rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an
exercise is performed, the effectiveness of the exercise will be reduced. 

Summary of Contents for 831.159370





























Reviews: