Dual Channel Receiver RXX 2322 230V
D
UAL
C
HANNEL
R
ECEIVER
RXX 2322 230V
The miniature RXX 2322 230V dual channel radio receiver al-
lows remote control activation of electric and electronic devices
when coupled with one or more transmitters.
-
RES 2322 230V
: Narrow band ( up to 66 Bit )
433,92 MHz
-
RXH 2322 230V
: Narrow band ( up to 66 Bit )
868,30 MHz
I
MPORTANT
FOR
THE
USER
- The device can be used by children over 8 years of
age and persons with reduced physical or psychologic-
al abilities or with little knowledge and experience only
if supervised or educated in its operation and safe use,
in order to also understand the dangers involved in its
use.
- these instructions are also available at the website
www.seav.it
- Do not allow children to play with the device and keep
the remote controls out of their reach.
- Frequently examine the system to detect any signs of
damage. Do not use the device if it is in need of repair
work.
-Always remember to disconnect the power supply be-
fore carrying out any cleaning or maintenance.
- Cleaning and maintenance must not be carried out by
unsupervised children
- ATTENTION: keep this instruction manual safe and
observe the important safety requirements contained
herein. Failure to comply with the requirements may
cause damage and serious accidents.
I
MPORTANT
FOR
THE
INSTALLER
1)Check that the location where the installation is
located enables compliance with operating temperature
limits specified for the device.
2)Once installation is finished, it is recommended that
all necessary checks be performed (appropriate
programming of the control panel and correct
installation of safety devices) to ensure that compliant
installation has been performed.
3)Fix the receiver to a wall, using the relevant support
which is fitted to the casing, in such a way as to leave
said support facing downwards and insert the fixing
screws in the special holes.
4)The receiver does not have any type of isolating
device for the 230 Vac line. It is therefore the
responsibility of the installer to set up an isolating
device inside the system. It is necessary to install an
omnipolar switch, surge category III. It must be
positioned to provide protection from accidental
closing, pursuant to point 5.2.9 of EN 12453.
1)For proper functioning of the radio receiver, if using
one or more receivers, the installation at a minimum
distance of at least 3 metres one from the other is
recommended.
13) Furthermore, care is required when drilling holes in
the outside casing where connecting and power supply
cables will pass, and when assembling the cable
glands, so that everything is installed so as to maintain
the panel's IP protection characteristics.
Radio Receivers
RES 2322 230V – RXH 2322 230V
comply with the specifications of the Directives:
RED 2014/53/EU, EMC 2014/30/EU, LVD 2014/35/EU.
The full text regarding the EU Declaration of Conformity
is available from the following Internet address:
http://www.seav.it
T
ECHNICAL
D
ATA
- Work frequency:
see model
- Power supply:
230VAC
- Max. consumption:
5W
- Op. transmitters:
Fixed code 12-18-32 Bit
Rolling Code 66 Bit
- TX codes that can be memorised (CH1 + CH2) :
250 Max
- Control relay:
230VAC 5A
- Working temperature:
-10÷55°C
- Board dimensions
: 99x50x28mm
- Container
: ABS V-0
- Protection rating
: IP 44 for internal use
CN1 T
ERMINAL
B
OARD
C
ONNECTIONS
1: Power supply 230 VAC
2: Power supply 230 VAC
CN2 T
ERMINAL
B
OARD
C
ONNECTIONS
1: “Normally open” contact output CH1
2: “Normally open” contact output CH1
3: “Normally open” contact output CH2
4: “Normally open” contact output CH2
1
Rev. 1.0 13/02/2018
GB
