Seav LG 2212 New Manual Download

Page: 16 / 74

B) AUT / S-S ( Pre-flashing / Courtesy Light ) :

The control unit is supplied by the manufacturer with Pre-

flashing and Courtesy Light functions disabled. If you wish to

enable the Pre-flashing function, proceed as follows: make sure

that you have enabled Extended Menu 2 (T. PAUSA LED and
RIT. ANTE LED start flashing simultaneously), with the SEL key

positioned on the flashing of AUT/ S-S LED then press the SET

key, the AUT/S-S LED will simultaneously stays on steadily and

programming is completed. If you wish to enable the Courtesy
Light, repeat the operation described above, pressing the SEL

button twice instead of once (the AUT / S-S LED will flash

rapidly). Repeat the operation to restore the initial configuration.

Pre-flashing** function

The flashing beacon 230 Vac is always

activated 3 seconds before the automation starts any type of

motion.

Courtesy Light Function:

The Flashing beacon 230 Vac

output will be activated for 3 minutes, each time that an opening
command is given.

C) CODE ( Flashing beacon function ) :

The control unit is supplied by the manufacturer with the
flashing beacon function during the Pause Time disabled. If you

wish to enable the function, proceed as follows: make sure that

you have enabled Extended Menu 2 (T. PAUSA LED and RIT.

ANTE LED start flashing simultaneously), with the SEL key
position on the flashing of CODE LED then press the SET key,

the CODE LED will simultaneously stay on steady and

programming is completed. Repeat the procedure to restore the

previous configuration.

D) INB. CMD. AP. LED ( SOFT START ) :

The control unit is supplied by the manufacturer with the Soft

Start function disabled. If you wish to enable the function,

proceed as follows: make sure that you have enabled Extended
Menu 2 (T. PAUSA LED and RIT. ANTE LED start flashing

simultaneously), with the SEL key position on the flashing of

INB.CMD.AP LED then press the SET key, the INB.CMD.AP

LED will simultaneously switch on permanently and
programming is completed. Accordingly, every time the gate

starts motion the control unit will control motor start-up,

increasing the power gradually from minimum to maximum in

the first two seconds of operation. Repeat the procedure to
restore the previous configuration.

E) T. MOT. (Electric Lock activation CMD PED.) :

The control unit is supplied by the manufacturer with the
activation of the electric lock through the disabled Pedestrian

command. If you wish to enable the function, proceed as

follows: make sure that you have enabled Extended Menu 2 (T.

PAUSA LED and RIT. ANTE LED start flashing simultaneously),
with the SEL key position on the flashing of T.MOT. LED then

press the SET key, the T.MOT. LED will simultaneously switch

on permanently and programming is completed. The activation

of the electric lock function through the Pedestrian command, is
used when you have, for example, a sliding gate with a door

next to the Pedestrian passage. Accordingly, the gate can be

opened with the PUL commands as well as from the Pedestrian

door using the electric lock with the PED. commands for 2
seconds. Repeat the procedure to restore the previous

configuration.

F) T. MOT. PED. LED ( PUL and PED command functions ) :

The control unit is factory supplied with PUL control input

operation for the connection of a cyclical primary control button

(NA) and a PED input for the connection of a cyclical Pedestrian

command button (NA). If you wish to select another mode of
function of the PUL and PED inputs, proceed as follows: make

sure that you have enabled Extended Menu 2 (T. PAUSA LED

and RIT. ANTE LED start flashing simultaneously), by using the

SEL key select the flashing T. MOT. PED. LED and press the

SET button: T. MOT. PED. LED stays steadily lit and

programming is complete.

Accordingly, the PUL input makes it possible to connect a
button (NA) for the Opening phase only, and the PED input for

connection to a button (NA) for the Closing phase only. Repeat

the procedure to restore the previous configuration.

EXTENDED MENU 3

The control unit is supplied by the manufacturer with only the

option of directly selecting the functions listed in the main menu.

To enable power programming functions for deceleration

carried out by the control unit, proceed as follows: open
Extended Menu 2 (as instructed in the respective section), then

press and hold the SET key for 5 seconds, after which the T.

PAUSA LED and RIT. ANTE LED will start flashing alternately

and then simultaneous, in this way there will be 30 seconds to
select the desired deceleration using the SEL and SET keys,

then, after a further 30 seconds, the control unit returns to the

main menu.

---------------------- EXTENDED MENU 3 -----------------

Level Leds On

1                                                  1-2 MOTORS
2                                         1-2 MOTORS - AUT / S-S
3                                  1-2 MOTORS - AUT / S-S - CODE
4                       1-2 MOTORS - AUT / S-S – CODE - INB. CMD. AP.
5             1-2 MOTORS - AUT / S-S – CODE - INB. CMD. AP -  T. MOT.
6  1-2 MOTORS - AUT / S-S - CODE - INB. CMD. AP - MOT. T. - PED. MOT. T.

Programming Motor Power during Deceleration

The control unit allows you to programme the motor power to

which the deceleration phase will be carried out.
It is possible to choose between 6 different levels of power:

every combination of lit Leds corresponds to a level according

to the table above; in other words, starting from the lowest led

(1-2 MOTORS LED) and moving upwards, each Led
corresponds to a higher power level. Using the SEL key it is

possible to scroll through the different power levels; for every

selected power level, the highest respective LED will flash (for

example, if level 4 is selected the 1-2 MOTORS AUT/S-S and
CODE LEDs light up steady, whereas the INB CMD. AP LED

flashes); press SET to confirm.

Level 3 is selected in the default configuration.

RESET :